Barco R9001280 manual

Connections

Straps on module level :

Floating or non-floating input.
Red :	J3	: strap "yes" : non floating	strap "no" : floating
Green : J4		: strap "yes" : non floating	strap "no" : floating
Blue :	J5	: strap "yes" : non floating	strap "no" : floating
H/C :	J6	: strap "yes" : non floating	strap "no" : floating
V : J7 : strap "yes" : non floating			strap "no" : floating

Factory preset : strap "yes", non floating input

Sync selection.

J8 : separate sync or sync on green.

Factory preset : separate sync.

Connecting a computer, e.g. IBM PC (or compatible), Apple Macintosh to the RS 232 input of the projector.

The projector has a RS232 port that allows it to communicate with a computer.

Applications : remote control and VISION communications.

a)remote control :

-easy adjustment of projector via IBM PC (or compat- ible) or MAC connection.

-allow storage of multiple projector configurations and set ups.

-wide range of control possibilities.

-address range from 0 to 255.

b)VISION communications :

-sending VISION to the projector or copying the VISION from the projector to a hard memory device.

Set up of the baud rate for communication with a computer.

The communication speed between projector and computer, e.g. PC or MAC, has 8 possible speeds. With DIP switches S2(1,2,3) on the controller unit, it is possible to select the baud rate (communication speed).

Gaining access to the DIP switches

Power down the projector and unplug the power cord from the wall outlet.

Turn both lock screws with a screwdriver or coin counter clock- wise.

Lift up and pivot the top cover. Attention : the cover is not secured with an incorporated support. When opening, turn it over slowly and lay it down on the second part of the top cover.

The processor module with the DIP switches is located on top, the front left side (seen from the front of the projector, see next page).

J8 Sync selection

Separate sync

Sync on green

J3

J4

J5

J6

J7

Non-Floating

Floating

Floating or non floating input

DIAGNOSTICS

IR-ACKNOWLEDG ED CODE IR-RECEIVER

RS232 OUT

IR-RECEIVED

RS232 connection

5975348 BARCOVISION 8200 280497		6-7

Image 25

Barco R9001280 owner manual Set up of the baud rate for communication with a computer

Contents

Vision Page Date Rev Art. No 280497 R5975348 Barco Projection Systems Noordlaan Kuurne Belgium Barco nv/Projection Systems Table of Contents Service Mode Installation instructions Safety InstructionsGeneral safety instructions Mains lead AC Power cord with CEE 7 plug Remarque sur la Sécurité Instructions pour l’installationFédéral communication commission FCC statement Prescriptions de securite générales On Cleaning On InstallationOn Servicing On Repacking Entretien et Réparation ’InstallationNettoyage Ré-emballage Unpacking Projector dimensionsBarcovision Battery installation in the RCU Environment Installation guidelinesWhat about ambient light ? Which screen type? How to install a projection lens? Where to install the projector?Definitions of the Abbreviation on drawings Inputs and computer video format input compatibility Front panel terminology Location and Functions of ControlControl Panel Terminology Local keypad Terminology Remote controlRCU Installation SET UP System Settings Switching on Power mains cord connectionConnections Fuses Input connections Switching to stand-by Switching offInput module insertion into the projector Straps on module level Video/S-video input module RGB input selection RGB analog input module Component input selection Component input moduleIndication on the input slot menu Input selection RGB3S/RG3sB input module Set up of the baud rate for communication with a computer Connecting a VS05 to the projector Connecting a Rcvds 05 to the projectorConnecting an IR Remote Receiver 800 to the projector OFF OFF OFF On OFF OFF OFF on OFF Hardware set up of the projector address How to use the RCU?Controlling Projector address How to program an address into the RCU? How to display a projector address?Picture controls with direct access How to control the projector or projectors How to get source information? Software version How to get a summary of your projector? Installation of the settings for a input source Source SET UPInput selection Enter Edit file Edit File Options Copy Rename Delete MoveOptions Source Set Up Video offset Signal operationsGain Smoothness Gain adjustment per colorStill video On/Off Sync Fast/Slow Zoom/pan Screen operations Moves the window upwards Picture Compresses the picture in the horizontal direction Conversion ConfigureGeometry Picture Control in Adjustment Mode How to activate the password function? Service ModeStart up of the Service mode 10-1 0000 Convergence adjustment of the LCD panels Red on green convergence Green focusing Blue on green convergence Reset Lamp Run Time Modify passwordLamp Run Time History 10-6 Barcovision 8200 Standard source set up files Standard Source SET UP Files Standard Source Set Up Files Battery replacement in the RCU Battery Replacement in the RCU Lens Cleaning Procedure Focusing the lensLenses Lenses Source numbers 90 Source Numbers 90 Insert Card