Barco R9001280 8

Source Set Up

8-1

5975348 BARCOVISION 8200 210497

8SOURCE SET UP

Input selection

Use the numeric keys on the RCU or use the local key pad to select the corresponding input

slot.

The source settings has to be installed for each source when these sources are displayed for

the first time.

Installation of the settings for a input source.

Start up the adjustment mode by pressing ENTER. The main menu will be displayed.

Push the joy stick key forward or backward to highlight File service.

ENTER selects the highlighted item and continues to the next step. EXIT returns always to the

previous step.

* Select the LOAD function to install the correct file. Only the files which can be used for this

source will be shown. (See appendix A for a list of the standard available files).

File annotation :

xxxxxxxx.xxx (Sx, xxxXxxxi)

MAIN MENU

832c

Picture Control

System Settings

File service

Service Mode

I or blank : i = interlaced, blank = not interlaced

xxxXxxx : active pixel rating

Sx : source number

xxx : file extension, first character is C (for custom made files) or S (for standard

files).

The second and third character is used for a following number (=file index)

file index for custom files : 00 to 63.

xxxxxxxx : base name, 8 characters.

The projector leaves the factory with different custom files installed.

Push the control disk up or down to select LOAD and press ENTER to display the Load

menu.

LOAD FILE

pal .s1 (s1. 675x278i)

pal .c50 (s1. 675x278i)

secam .s3 (s3. 675x278i)

849

pal .c50 (s1. 675x278i)

Search pattern : [Fit]

FILE SERVICE

847

Load

Edit

Rename

Copy

Move

Delete

Options

The Load menu displays the corresponding files depending on the installed search pattern.

This search pattern can be "Fit" or "All". To change the search pattern, push the control disk

to the right to select "search pattern" and press ENTER to change the annotation between

brackets.

"All" : all available files will be displayed.

"Fit" : only the best fitting files will be displayed (with a distinction of ± 2 lines and line duration

distinction of ± 300 ns)

Contents

Main Page BARCO PROJECTION SYSTEMS OWNER'S MANUAL Page Table of Contents TABLE OF CONTENTS i Table of Contents 1 Installation instructions Federal communication commission (FCC statement) General safety instructions. ON SAFETY Remarque sur la Scurit Instructions pour linstallation Fdral communication commission (FCC statement) Prescriptions de securite gnrales. SECURITE On Installation On Servicing On Cleaning On Repacking On illumination LInstallation Entretien et Rparation Nettoyage R-emballage Eclairage 2 Unpacking allow air circulation via the built-in dust filter at the bottom. Projector dimensions Pull To open Unpacking and Dimensions Battery installation in the RCU. Installation Guidelines 3 Installation guidelines * Environment * What about ambient light ? * Which screen type? Installation Guidelines * Where to install the projector? Definitions of the Abbreviation on drawings Lens type selection. Inputs and computer video format input compatibility : 4 6 Front panel terminology 7 8 11 Location and Functions of Control b. Remote control 15 1 2 3 4 5 6 7 8 9 10 11 12 13 14 5 Installation Set Up 6 Power (mains) cord connection Fuses Switching on Warning : Using a lamp for more than 1000 hours is dangerous, the lamp could explode. Input connections. Input module insertion into the projector : Switching to stand-by. Switching off Video/S-video input module ADJUST or ENTER EXIT Straps on module level. RGB analog input module. RGB input selection : ENTER RGB-SS [CV] RGB-SS [CS or HS&VS] Component input module. On Component input selection : Indication on the input slot menu : RGB3S/RG3sB input module. Input selection : Indication on the input slot menu : Set up of the baud rate for communication with a computer. Connecting a RCVDS 05 to the projector. Connecting a VS05 to the projector Connecting an IR Remote Receiver 800 to the projector. 7 How to use the RCU? Projector address a. hardware set up of the projector address. b. How to control the projector or projectors. How to display a projector address? How to program an address into the RCU? Picture controls with direct access. Brightness Control 'brightness' How to get source information? EXIT How to get a summary of your projector? Main Lamp Serial number Projector Serial number lamp run time 8 Input selection Installation of the settings for a input source. MAIN MENU LOAD FILE Edit file EDIT FILE "Vertical" "Horizontal" Read/Write Read AMDS Options EDIT FILE OPTIONS Vertical refresh [sync/async] Vertical sync polarity Rename Copy COPY FILE RENAME FILE Move MOVE FILE ENTER Delete DELETE FILE Page 9 Signal operations Screen operations Signal operations. MAIN MENU Gain adjustment per color Smoothness Still video [On/Off] Sync [Fast/Slow] ENTER Screen operations Picture Control "Picture" "Window" Zoom/Pan Page Picture Page Configure geometry Geometry Configure conversion Page SERVICE MODE How to activate the password function? Invalid Password Enter password Service mode Convergence adjustment of the LCD panels. Gaining access to the DIP switches Green Convergence Connections Test pattern Red on green Test pattern Blue on green Hatch Modify password 'Modify password' Reset Lamp Run Time Lamp Run Time History Lamp Run time History Reset Lamp Run Time Service Mode Standard Source Set Up Files STANDARD SOURCE SET UP FILES LACT : A Standard source set up files. Page Battery Replacement in the RCU BATTERY REPLACEMENT IN THE RCU B Battery replacement in the RCU. Lenses C moisten the cloth or tissue Focusing the lens Lens Cleaning Procedure Cleaning procedure for HD(1.5-3:1) lens and HD(3-5.3:1) lens. Lenses Lenses Source Numbers 90 - 99 D Source numbers 90 - 99 Insert Card INSERT CARD 5975348 BARCOVISION 8200 210497 RCU