Emerson CF200n100 owner manual Preset Memory Feature, General, Installation of Battery, Dures

Page 4

BP7354 CF200 9/19/07 11:30 AM Page 4

2. Remove the fan motor and housing assembly from the protective plastic bag. Place the fan assembly into the lower foam pad with the bottom of the motor facing up.

The lower foam pad serves as a holder for the fan during the first stages of assembly.

Preset Memory Feature

Your remote control receiver is equipped with a preset memory feature. The receiv- er will remember the light intensity and fan speed when the light and fan are turned off from the wall switch. When the wall switch is turned back on, the lights and fan will resume operation as they were prior to the

General

switch being turned off.

Your Emerson ceiling fan comes equipped

Installation of Battery

with a remote control transmitter and a

 

remote control receiver. This remote con- trol systems is designed to control your ceiling fan speed and light intensity.

NOTE: An optional SW101 Wall Control (not supplied) may also be used with the remote control receiver supplied with your ceiling fan.

IMPORTANT

This Owner’s Manual is divided into two sections. The first section,

REMOTE CONTROL PROCEDURES, describes how to install the 9-volt alka- line battery (not supplied) in the remote control transmitter, and how to set the operating frequency of the transmitter and receiver. These instructions must be performed prior to the installation of the ceiling fan as described in the second section, CEILING FAN PROCE-

DURES.

1. Remove the battery cover by pressing firmly below the arrow and sliding the cover off the control (Figure 1).

2. Engage the connector in the transmitter with the terminals of a 9-volt alkaline battery (not supplied).

 

RECEIVER

 

 

CODE

 

 

SWITCH

 

SWITCH

ON

 

 

 

LEVERS

1 2 3 4

 

BATTERY

 

e

 

 

y

COVER

 

r

 

B

 

 

t

 

 

t

 

 

a

 

BATTERY

 

 

CONNECTOR

BATTERY

 

REMOTE CONTROL

 

 

Figure 1

TRANSMITTER

 

 

 

REMOTE CONTROL

PROCEDURES

General

The remote control system is designed to separately control your ceiling fan and light intensity. There are four push buttons on the transmitter (HI, MED, LOW, OFF) to set the fan speed and turn the fan off. The

light push button turns the light on and controls the light intensity. The red indicator light will illuminate while any but- ton is pressed, indicating that the battery is good.

Setting Operating

Frequency of Transmitter

and Receiver

Your remote control transmitter and receiver have code switches which must be set on one of 16 possible code combi- nations. The four levers (numbered 1, 2, 3, and 4) on the switches are factory-set in the ON (up) position. Do not use this setting. Change the switch settings as follows:

1.On the remote control transmitter, locate the code switch just above the battery compartment (Figure 1).

4

U.L. Model No.: CF200

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Cityscape Safety Instructions Date CodeMaterials Tools Needed for AssemblyUnpacking Instructions Preset Memory Feature Installation of BatterySetting Operating Frequency of Transmitter Receiver GeneralHow to Assemble Your Ceiling Fan Electrical RequirementsLight Fitter White Wires Black Wire Blue Switch Housing AssemblyConnector Switch Housing Assembly Blade Flange Motor HUBPIN Hanger Ball Downrod Setscrew Hairpin ClipSetscrew Motor Clevis PINMotor Cover Housing Decorative ROD Screw Decorative ROD AssemblyROD Support Grommet ScrewsHow to Hang Your Ceiling Fan Ceiling AT Least FloorOutlet BOX TWO Screws Supplied With TABHow to Wire Your Ceiling Fan StudBlack White Ground REDBlack Blue Ceiling CoverReversing Switch Installation Storage BracketOperating Your Ceiling Fan MaintenanceAccessories Important Care InstructionsTrouble Shooting Trouble Probable Cause Suggested RemedyRepair Parts Listing DescriptionLimited Warranty

CF200n100 specifications

The Emerson CF200N100 is a cutting-edge fan controller designed to provide optimal air circulation and temperature control in various environments. Known for its efficiency and advanced features, this model has found applications in residential, commercial, and industrial settings.

One of the standout characteristics of the CF200N100 is its energy efficiency. Designed to operate with minimal power consumption, this unit helps reduce electricity costs while maintaining effective airflow. It integrates advanced technologies that allow for precise control over fan speed, facilitating customized air distribution according to specific needs.

The CF200N100 employs a microprocessor-based control system that enhances stability and reliability. This technology allows for intelligent programming, enabling users to set specific temperature thresholds and operational schedules. With a user-friendly interface, the controller simplifies adjustments and makes it convenient to monitor performance.

Another significant feature of the Emerson CF200N100 is its compatibility with various fan types and setups. Whether used in ducted systems or standalone fans, the controller can adapt to different configurations, making it a versatile choice for any installation. Its flexibility also extends to integration with existing HVAC systems, providing seamless functionality in retrofitting scenarios.

The unit showcases various safety features, including overcurrent protection and temperature monitoring, ensuring that both the device and connected fans operate within safe limits. This not only prolongs the lifespan of the equipment but also enhances user peace of mind.

For communication, the CF200N100 is equipped with advanced connectivity options, allowing for integration with smart home systems. Users can control fan settings remotely, making adjustments from anywhere through compatible devices. This capability not only adds convenience but also allows for real-time monitoring of environmental conditions.

The design of the Emerson CF200N100 is compact, ensuring that it can be installed in tight spaces without compromising performance. Its robust construction contributes to its durability, ensuring that it withstands the demands of continuous operation.

In summary, the Emerson CF200N100 is a feature-rich fan controller that promises efficiency, flexibility, and advanced control. Its energy-saving technologies, user-friendly design, and integration options make it an excellent choice for anyone looking to improve their air circulation systems. Whether for residential use or in more demanding commercial settings, the CF200N100 stands out as a reliable solution in modern climate control management.
Top Page Image Contents