Sterling D48160s manual Safely Clearing a Jam

Page 76

OPERATION

SECTION 5-5

Safely Clearing a Jam

TURN OFF AND LOCKOUT the power per OSHA 1910.147 OR ANSI Z244.1-1982 (Lockout/Tag out of Energy Sources).

If it is not possible to lock out the power, have an electrician remove the fuses.

Make sure the rotor has come to a complete stop.

The hydraulic cylinders or jackscrews, which open the machine, should not operate until the rotor is completely stopped. If you discover that the hydraulic cylinders or jackscrews DO operate while the rotor is still turning, immediately shut down the machine and call for maintenance to adjust it.

Wear gloves to protect against injury from the rotor or bed knives.

When you REVERSE the jackscrew operating direction, always ALLOW THE JACKSCREW MOTOR TO COME TO A COMPLETE STOP. Release the control switch and allow a minimum of 5 seconds before switching to the opposite operating position. If you don't allow this pause, the JACKSCREW AND OTHER COMPONENTS MAY BE SEVERELY DAMAGED.

OPEN THE CUTTING CHAMBER

Open the screen cradle per instructions in Section 6-6 entitled Screen Replacement. Open the cutting chamber per instructions in Section 6-9 entitled Cutting Chamber Access.

NEVER ATTEMPT TO FREE A JAMMED MACHINE BY PLACING YOUR HANDS ON THE ROTOR, ON THE KNIVES, OR INSIDE THE CU1TING CHAMBER.

KEEP YOUR HANDS CLEAR OF THE ROTATIONAL PATH OF THE ROTOR KNIVES.

76

Image 76

Contents Sterling,Inc Refer to this Sheet When Ordering Parts Sterling, IncTable of Contents Settings and Adjustments Topic SECTION/PAGE Table of Contents Adjustable Rotor Knives…………………………………………………………………4-35 OperationMaintenance From previousMaintenance TroubleshootingParts Lists and Drawings Page What is a GRANULATOR? IntroductionLearn Machine Safety SectionFollow the Safety Instructions Rotating Knives Safety PlateOpening Hopper Safety Plate Guards Safety Plate Jackscrew Reversing OperationSafety Instruction Plate Hazardous Voltage Safety PlateRotating Knives Safety Plate Motor Rotation Safety PlateSafety Clothing & Practices Keep Your Work Area Safe Wear Protective ClothingKeep CO-WORKERS OFF the Machine Machine Opening Devices Be Sure the Rotor is Motionless Before Opening MachineSection Open the Cutting ChamberClear the JAM Restart the GranulatorMachine and Controls BP 2400 Series Granulator Right Front Quarter View BP 2400 Series Granulator Left Rear Quarter View Section Overview Uncrate the GranulatorAllow Adequate Work Space Section Move the Granulator to ITS Work SiteLevel the Granulator Remove the Protective Coating Electrical Wiring Section Check for Mechanical Interferences SET UP the Machine FunctionsCheck Rotation of Motors Interlock Switch Test Procedure Alternate Test for the Interlock SwitchesInstallation Alternate Test for the Interlock Switches from previous Test the Zero Speed SensorLubrication Test the Zero Speed SensorSettings and Adjustments Release the Cutting Chamber Fasteners Open the Cutting Chamber InterlockSee -10 page 87 for Cutting Chamber Opening Instructions Install the Rotor Locating PIN Remove the BED Knives Loosen the Mounting ScrewsRemove the First Knife Clamp or Shield Replace the Upstroke BED Knife Replace the Upstroke Knife ClampGAP Adjustment Tips Replace the Downstroke BED KnifeReplace the Downstroke Knife Shields Check the BED KnivesCheck the Knife GAP Measure the Knife GAPSET the Downstroke Knife Shield Tighten the Screws to Final Torque Finalize Installation of Upstroke BED KnifeSee -11 page 88 for Cutting Chamber Closing Instructions Close the Cutting Chamber Safety Interlock Fasten the Cutting ChamberBasic Facts about the Knives See -10 page 87 for Cutting Chamber Opening Instructions Remove the Mounting Screws Lock the RotorRemove the Rotor Knives Clean Parts for Reassembly PhotoGAP Adjustment Tips Measure the Knife GAPCheck the Knife GAP Tighten the Screws to Final TorqueFasten the Cutting Chamber Remove the Drive Guard Cover Install the Matched Belts Inspect the Drive BeltsRemove the Belts Tighten the Belt TensionCheck the Pulley Alignment Measure the Belt SpanCalculate the Allowable Belt Deflection Measure the Deflection ForceCompare Measured Force to Recommended Force Adjust the Belt TensionTighten the Motor Base Bolts Replace the Drive Guard Cover Setting and Adjusting the Chamber Jackscrew Cutting Chamber Open Setpoint Adjust the Jackscrew OPEN-POSITION Limit Switch SET the Jackscrew CLOSED-POSITION Limit Switch If the Motor Stops Before the Cutting Chamber ClosesSET the Jackscrew CLOSED-POSITION Limit SET & Test the Mounting Bracket Limit SwitchChamber Stops Before IT Closes but Motor Continues to RUN From previous Close the Cutting Chamber Safety Interlock Retract the Screen Cradle Retainers Cradle Open Position Adjust the Cradle OPEN-POSITION Limit Switch Check the Cradle CLOSED-POSITION Switch Close the Screen Cradle Retainers Adjust the Cradle CLOSED-POSITION Limit SwitchClose the Screen Cradle Interlock Adjust the Sensor Position Zero Speed SensorZero Speed Sensor Operation Control CircuitKnife Length Setting Rotor Knife Installation Into FixtureRotor Knife Preparation Knife Length SETTING-INSPECTION Adjustable Rotor Knife InstallationHydraulic Opening Position Switches Hydraulic Pump Operation Operation Check the Motor Rotation Direction Discharge AIR AdjustmentRUN the Motor Cleaning the Discharge Transition Shut Down the MachineSafely Clearing a Jam Maintenance Periodic Maintenance Schedule Check Daily Weekly MonthlyBelt Tension Knife Screw TorqueScreen Condition Infeed Flap Condition Upper Chamber Pivot ARM-SCREWSOpen the Screen Cradle Interlock Retract the Screen Cradle RetainersSee -12 page 90 for Screen Cradle Lowering Instructions Remove the Screen Replace the ScreenMaintenance Close the Screen Cradle Interlock Cutting Chamber Access Open the Cutting Chamber with Jackscrews Open the Cutting Chamber with HydraulicsClose the Cutting Chamber with Jackscrews Fasten the Cutting Chamber Lower Raising the Screen Cradle with Jackscrews Rotor Knife Sharpening BED Knife Sharpening Test Equipment Troubleshooting ChartLocating Trouble Section Mechanical Faults Problem Probable Cause Remedy Electrical FaultsBP2400 Series Parts List and Drawings 100 Parts Identification Drawing No. A-48050 Sheet 3 Parts Identification Drawing No. A-48050 Sheet 4 Parts Identification Drawing No. A-48150 Sheet 1 Parts Lists and Drawings Parts Identification Drawing No Sheet 1 Parts Identification Drawing No -460 Sheet 1 Wiring Diagram Drawing No. A-399598 Sheet 1 108 Drawing No -1 Sheet 1 Wiring Diagram for Hydraulics Drawing No. D-499061 Sheet 1 Wiring Drawing No. D-499044 Sheet 1 112 113