Patton electronic 4960 Compliance, Radio and TV Interference, FCC Part 68 Acta Statement, Safety

Page 47

SmartNode 4960 Getting Started Guide

A • Compliance information

 

 

Compliance

EMC

•FCC Part 15, Class A

•EN55022, Class A

•EN55024

Safety

•UL 60950-1/CSA C22.2 N0. 60950-1

•IEC/EN60950-1

•AS/NZS 60950-1

PSTN Regulatory

•FCC Part 68

•CS-03

•TBR 12 & 13 (E1)

•AS/ACIF S016:2001 (E1)

•AS/ACIF S043:2003 (G.SHDSL card)

Radio and TV Interference

The SmartNode router generates and uses radio frequency energy, and if not installed and used properly-that is, in strict accordance with the manufacturer’s instructions-may cause interference to radio and television reception. The SmartNode router have been tested and found to comply with the limits for a Class A comput- ing device in accordance with specifications in Subpart B of Part 15 of FCC rules, which are designed to pro- vide reasonable protection from such interference in a commercial installation. However, there is no guarantee that interference will not occur in a particular installation. If the SmartNode router does cause interference to radio or television reception, which can be determined by disconnecting the unit, the user is encouraged to try to correct the interference by one or more of the following measures: moving the computing equipment away from the receiver, re-orienting the receiving antenna and/or plugging the receiving equipment into a different AC outlet (such that the computing equipment and receiver are on different branches).

FCC Part 68 (ACTA) Statement

This equipment complies with Part 68 of FCC rules and the requirements adopted by ACTA. On the bottom side of this equipment is a label that contains—among other information—a product identifier in the format US: AAAEQ##TXXXX. If requested, this number must be provided to the telephone company.

The method used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA.

If this equipment causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. But if advance notice isn’t practical, the telephone

Compliance

47

Page 46 Page 48
Image 47
Page 46 Page 48
Contents SmartNode 4960 Series Mailsupport@patton.com Summary Table of Contents Table of Contents Shdsl Basic Configuration Cabling List of Figures List of Tables Structure About this guideAudience Safety when working with electricity PrecautionsGeneral conventions Typographical conventions used in this documentGeneral observations Node General information Chapter contentsSmartNode SmartNode 4960 overviewSmartNode 4960 models with integrated G.SHDSL interface SmartNode 4960 rear panel ports are described in table SmartNode 4960 rear panelWAN ETH 0/0 SN4960/4E SmartNode 4960 front panelLED Applications overview Application-Edge intelligence of enterprise communication IntroductionHow it works Application-Multi-service Isdn Internet telephony IADApplications overview SmartNode installation Network information Planning the installationNetwork Diagram Site logInstalling the gateway router Connecting the 10/100/1000Base-T Ethernet LAN and WAN cables Connecting the power supply Initial configuration Connecting the SmartNode to your laptop PC Connecting the SmartNode to your laptop PCChanging the WAN IP address Factory-default IP settingsLogin Configuring the desired IP addressLAN Connecting the SmartNode to the networkLoading the configuration optional Load a new application image SmartWare via Tftp BootloaderStart Bootloader Start-up with factory configurationRedBoot ipaddress -g gateway Xmodem ymodem -b Load a new application image SmartWare via the serial linkAdditional information Shdsl Basic Configuration Configuring PPPoE Line SetupProfile napt WAN Configuration SummaryUsing PVC channels with PPPoE Setting up permanent virtual circuits PVCUsing PVC channels in bridged Ethernet mode Diagnostics Troubleshooting DSL ConnectionsContacting Patton for assistance Patton support headquarters in the USA Warranty coverageContact information RMA numbers Out-of-warranty serviceAppendix a Compliance information FCC Part 68 Acta Statement SafetyCompliance Radio and TV InterferenceCE Declaration of Conformity Industry Canada NoticeAppendix B Specifications Data connectivity Voice processing signalling dependentVoice connectivity Voice routing-session router Voice signallingFax and modem support Physical IP servicesManagement SystemDSL Shdsl Daughter Card if applicableSmartNode Model SysObjectID Identification of the SmartNode devices via SnmpAppendix C Cabling Console Connecting a serial terminalEthernet E1 PRI T1 PRI Appendix D Port pin-outs EIA-561 RJ-45 8-pin port Console portShdsl port PRI portAppendix E SmartNode 4960 factory configuration Introduction Appendix F End user license agreement End User License Agreement Other licenses Termination
Related manuals
Manual 67 pages 36.92 Kb

4960 specifications

The Patton Electronics 4960 is a cutting-edge solution designed to facilitate reliable, high-speed data communication over traditional copper telephone lines. This versatile device is particularly noted for its carrier-grade performance and is widely utilized in a variety of applications, from telecommunications to industrial automation.

One of the main features of the 4960 is its ability to support both T1 and E1 connectivity. This adaptability makes it an excellent choice for organizations that need to interface with different types of line configurations. The device offers a reliable method for transmitting voice and data without significant loss or degradation in quality. Enhanced echo cancellation technology further optimizes communication, ensuring clear transmission even in challenging network conditions.

The 4960 is equipped with advanced modulation techniques, including Adaptive Trellis Coding and Echo Cancellation. These technologies enable the device to maintain high throughput and resilience in fluctuating line conditions. This adaptation to network conditions makes the Patton 4960 well-suited for long-range communications, significantly extending the reach of WAN connections.

In terms of management and monitoring, the device boasts both SNMP support and a web interface that allows for straightforward configuration and real-time monitoring. The user-friendly interface is designed to provide network administrators with the necessary tools to troubleshoot and ensure optimal performance, reducing downtime and maintenance costs.

In addition to its robust architecture, the Patton 4960 integrates seamlessly into various networking environments. It can be deployed in a range of scenarios, such as connecting remote sites, supporting legacy equipment, or even functioning as a bridge for VoIP systems. The flexibility offered by the 4960 enhances its appeal across different sectors, from small businesses to large enterprises.

With built-in surge protection and a durable casing, the Patton 4960 is designed with reliability in mind, ensuring that users can count on consistent performance even in demanding environments. This dedication to robustness contributes to its reputation as a trusted device among IT professionals.

In summary, the Patton Electronics 4960 stands out for its combination of advanced features, compatibility, and ease of use. Its adaptability to both T1 and E1 lines, coupled with robust data transmission technologies, makes it a valuable asset for any organization seeking reliable communication solutions.
Top Page Image Contents