Patton electronic 4960 manual End User License Agreement

Page 66

SmartNode 4960 Getting Started Guide

F • End user license agreement

 

 

End User License Agreement

By opening this package, operating the Designated Equipment or downloading the Program(s) electronically, the End User agrees to the following conditions:

1. Definitions

A)Effective Date shall mean the earliest date of purchase or download of a product containing the Patton Electronics Company Program(s) or the Program(s) themselves.

B)Program(s) shall mean all software, software documentation, source code, object code, or executable code.

C)End User shall mean the person or organization which has valid title to the Designated Equipment.

D)Designated Equipment shall mean the hardware on which the Program(s) have been designed and pro- vided to operate by Patton Electronics Company.

2. Title

Title to the Program(s), all copies of the Program(s), all patent rights, copyrights, trade secrets and proprietary information in the Program(s), worldwide, remains with Patton Electronics Company or its licensors.

3. Term

The term of this Agreement is from the Effective Date until title of the Designated Equipment is transferred by End User or unless the license is terminated earlier as defined in section “6. Termination” on page 67.

4. Grant of License

A)During the term of this Agreement, Patton Electronics Company grants a personal, non-transferable, non-assignable and non-exclusive license to the End User to use the Program(s) only with the Designated Equipment at a site owned or leased by the End User.

B)The End User may copy licensed Program(s) as necessary for backup purposes only for use with the Des- ignated Equipment that was first purchased or used or its temporary or permanent replacement.

C)The End User is prohibited from disassembling; decompiling, reverse-engineering or otherwise attempt- ing to discover or disclose the Program(s), source code, methods or concepts embodied in the Program(s) or having the same done by another party.

D)Should End User transfer title of the Designated Equipment to a third party after entering into this license agreement, End User is obligated to inform the third party in writing that a separate End User License Agreement from Patton Electronics Company is required to operate the Designated Equipment.

5. Warranty

The Program(s) are provided as is without warranty of any kind. Patton Electronics Company and its licensors disclaim all warranties, either express or implied, including but not limited to the implied warranties of mer- chantability, fitness for a particular purpose or non-infringement. In no event shall Patton Electronics Com- pany or its licensors be liable for any damages whatsoever (including, without limitation, damages for loss of business profits, business interruption, loss of business information, or other pecuniary loss) arising out of the use of or inability to use the Program(s), even if Patton Electronics Company has been advised of the possibil- ity of such damages. Because some states do not allow the exclusion or limitation of liability for consequential or incidental damages, the above limitation may not apply to you.

End User License Agreement

66

Page 65 Page 67
Image 66
Page 65 Page 67
Contents SmartNode 4960 Series Mailsupport@patton.com Summary Table of Contents Table of Contents Shdsl Basic Configuration Cabling List of Figures List of Tables About this guide AudienceStructure Precautions Safety when working with electricityTypographical conventions used in this document General observationsGeneral conventions Node Chapter contents General informationSmartNode 4960 overview SmartNodeSmartNode 4960 models with integrated G.SHDSL interface SmartNode 4960 rear panel SmartNode 4960 rear panel ports are described in tableWAN ETH 0/0 SmartNode 4960 front panel SN4960/4ELED Applications overview Introduction Application-Edge intelligence of enterprise communicationApplication-Multi-service Isdn Internet telephony IAD How it worksApplications overview SmartNode installation Site log Planning the installationNetwork Diagram Network informationInstalling the gateway router Connecting the 10/100/1000Base-T Ethernet LAN and WAN cables Connecting the power supply Initial configuration Connecting the SmartNode to your laptop PC Connecting the SmartNode to your laptop PCConfiguring the desired IP address Factory-default IP settingsLogin Changing the WAN IP addressConnecting the SmartNode to the network LANLoading the configuration optional Start-up with factory configuration BootloaderStart Bootloader Load a new application image SmartWare via TftpRedBoot ipaddress -g gateway Load a new application image SmartWare via the serial link Xmodem ymodem -bAdditional information Shdsl Basic Configuration Line Setup Configuring PPPoEConfiguration Summary Profile napt WANSetting up permanent virtual circuits PVC Using PVC channels in bridged Ethernet modeUsing PVC channels with PPPoE Troubleshooting DSL Connections DiagnosticsContacting Patton for assistance Warranty coverage Contact informationPatton support headquarters in the USA Out-of-warranty service RMA numbersAppendix a Compliance information Radio and TV Interference SafetyCompliance FCC Part 68 Acta StatementIndustry Canada Notice CE Declaration of ConformityAppendix B Specifications Voice processing signalling dependent Voice connectivityData connectivity Voice signalling Fax and modem supportVoice routing-session router System IP servicesManagement PhysicalShdsl Daughter Card if applicable DSLIdentification of the SmartNode devices via Snmp SmartNode Model SysObjectIDAppendix C Cabling Connecting a serial terminal ConsoleEthernet E1 PRI T1 PRI Appendix D Port pin-outs Console port EIA-561 RJ-45 8-pin portPRI port Shdsl port Appendix E SmartNode 4960 factory configuration Introduction Appendix F End user license agreement End User License Agreement Termination Other licenses
Related manuals
Manual 67 pages 36.92 Kb
Top Page Image Contents