Hobart Welding Products 2250 specifications Weld Parameters

3-2. Weld Parameters

WIRE TYPE	WIRE	MACHINE				MATERIAL THICKNESS
GAS	SIZE	SETTINGS*	3/8	5/16	1/4	3/16	12GA	14GA	16GA	18GA	20GA	22GA
FLOW RATE
	.023”	VOLTAGE	–	–	6	5	4	3	3	2	2	1
	0.6MM	WIRESPEED	–	–	100	85	75	60	50	36	30	15
E70S–6	.030”	VOLTAGE	5	5	4	4	3	3	2	2	2	1
CO2	0.8MM
		WIRESPEED	66	65	58	50	45	36	22	16	8	0
20CFH	.035”	VOLTAGE	7	6	5	5	4	3	3	2	2	1
	0.9MM	WIRESPEED	70	65	56	50	44	30	20	10	0	0
	.045”	VOLTAGE	7	6	5	4	4	3	3	2	–	–
	1.2MM	WIRESPEED	60	50	40	36	34	30	25	20	–	–
	.023”	VOLTAGE	–	–	5	4	3	3	2	2	1	1
	0.6MM
		WIRESPEED	–	–	100	85	75	70	50	40	28	22
E–70S–6
	.030”	VOLTAGE	7	6	5	4	3	2	2	1	1	1
75% AR	0.8MM	WIRESPEED	100	85	76	70	60	46	36	22	10	8
25% CO2
	.035”	VOLTAGE	7	6	4	4	3	2	2	1	1	1
20CFH	0.9MM	WIRESPEED	82	70	60	55	48	40	26	10	0	0
	.045”	VOLTAGE	7	6	4	4	3	3	2	2	–	–
	1.2MM
		WIRESPEED	60	55	50	45	46	40	30	22	–	–
	030”	VOLTAGE	–	5	5	4	2	2	1	1	–	–
	0.8MM	WIRESPEED	–	50	58	50	30	20	10	0	–	–
E71T–GS
	.035”	VOLTAGE	6	5	4	3	2	2	1	1	–	–
FLUXCORE	0.9MM	WIRESPEED	50	40	38	30	20	10	0	0	–	–
	.045”	VOLTAGE	5	5	4	3	2	2	–	–	–	–
	1.2MM	WIRESPEED	46	40	30	20	0	0	–	–	–	–
E71T–GS	.035”	VOLTAGE	7	7	7	6	5	3	–	–	–	–
FLUXCORE	0.9MM	WIRESPEED	80	78	72	68	60	55	–	–	–	–
75AR/25CO2
	.045”	VOLTAGE	7	7	7	6	5	4	–	–	–	–
20CFH	1.2MM	WIRESPEED	70	65	60	50	42	36	–	–	–	–
ER308L	.023”	VOLTAGE	–	–	–	5	4	3	3	2	–	–
STAINLESS	0.6MM	WIRESPEED	–	–	–	100	80	60	52	22	–	–
90% HE
	.030”	VOLTAGE	–	–	6	5	4	3	3	2	–	–
7.5% AR	0.8MM	WIRESPEED	–	–	90	72	60	38	30	18	–	–
2.5% CO2	.035”	VOLTAGE	7	6	5	4	4	3	2	2	–	–
20CFH	0.9MM	WIRESPEED	75	70	70	64	62	35	20	14	–	–

*Do not change Voltage switch position while welding. Wire Speed is a starting value only, and can be adjusted while welding. Weld conditions also depend on other variables such as stickout, travel speed, weld angle, cleanliness of metal, etc.

OM-192 440 Page 17