RIDGID WL1200LS1 manual Mounting Right Side Table Top, Particle Board Table Top Carriage Bolt M6 x

Page 13

Mounting Right Side Table Top

1.Find the following:

1Particle Board Table Top

2.From the loose parts package find the following:

4M6 x 1.0-45 Carriage Bolts

4 M6 x 1.0 Hex Head Nuts

46.5 x 19 x 1.6 Flat Washers

46mm Lockwashers

3.The right side mounts similar to the left except there is no steel support plate.

4.Place carriage bolts, through the table top holes B and D as shown. Align the right side table top with the left side table top so that the two halves join end to end. Fasten in place with a washer, lockwasher and nut.

5.Securely tighten all nuts and bolts.

6.Adjust leveling feet as follows:

a.Move legset to desired location.

b.With a 14mm wrench loosen bottom nut.

c.Back off top nut by hand.

d.Raise or lower foot by adjusting bot-

tom nut using 14mm wrench.

e. Snug top nut against inside of leg by hand.

f. Tighten all four bottom nuts using 14mm wrench.

Particle Board Table Top

Carriage Bolt

M6 x 1.0-45

Flat Washer	Lockwasher	Nut Hex
6.5 x 19 x 1.6	6mm	M6 x 1.0

	Motor Mounting Plate		Right Side
	Motor Mounting Plate		Table Top
			Table Top
	C
	C		D
	A	B	D
	A	B	B
			B

C

C

Left Side

Table Top

C

13

Image 13

Contents +22 7851,1*/$7+ Safety Instructions For Wood Turning Lathe Table of ContentsKnow and Understand the Lathe Safety Symbols Before Using the LatheReduce the Risk of Dangerous Environment Use Recommended AccessoriesTo reduce the risk of injury from unexpected lathe movement Inspect your latheReduce the Risk of Accidental Starting Dress for safetyKeep Children Away Inspect Your WorkpieceDon’t Force Tool Before freeing jammed materialPower Supply and Motor Specifications Motor Specifications and Electrical RequirementsGeneral Electrical Connections Volt, 60 Hz. Tool InformationMotor Safety Protection Unpacking and Checking Contents Loose Parts Package Assembling Steel Legset AssemblyMounting Left Side Table Top Holes Used for Mounting Boards and Wood Lathe to Leg SetBoard/Side Support Particle Board Table Top Carriage Bolt M6 x Mounting Right Side Table TopMotor Mounting Plate Right Side Table Top Left Side Mounting Headstock Assembly Headstock Carriage Bolt M6 x Hex Head Nut HexBelt Guard Pan Head Thread Cutting Screw M5 x 0.8 x Pan ScrewM6 x Hex Head Screw Carriage Bolt Mounting the MotorHex Nut X 19 xAssembly Assembly Hex Hd Screw Tailstock Headstock, Tailstock, and Tool Rest AssemblyTube Large Tool Rest Assembly Pan Head Screw Mounting Rear FootNut Square Flat Washer M8 x X 19 x Nut Hex M6 xHex Nut 3/4-16 Live Center Tailstock Ram Dia Wood Dowel Foot Spur and Cup Center InstallationCheck Spindle Rotation Adjusting TailstockAligning Centers ScrewBed Getting To Know Your Wood LatheHeadstock Yellow Switch Key On-off SwitchChanging Speeds Basic Lathe OperationsDiagonal Lines on Both Ends Spindle TurningWood Tool Rest Faceplate Turning Basic Lathe Operations Indexing Woodworking Chisels and How to Use Them How To Use Your Ridgid Wood LatheSix Commonly Used Chisel Types Selection Of Chisels Theory Of TurningHow to Position Tool Rest for Circum- ference Cutting When You Can Cut, and When You Must ScrapeDiameter Approach Circumference Rest Face Edge How to Position Tool Rest for Circumference ScrapingUsing The Skew Using The GougeSupport Using Toe Edge does not cut Using Heel Cutting Edge AdvancedWrong RightUsing The Scraping Chisels Using The Parting ToolSpear Round Flat Point Nose Nose Roughing Off Finish Cutting Hand PositionsMaking Standard Cuts Cutting a Shoulder Smoothing a CylinderParting Tool Pencil Mark Pencil Skew Wrong Right Bevel Cutting Beads Cutting VeesPencil Marks Cutting Coves ConcavesCutting Coves Making Long Convex CutsMaking Long Taper Cuts How To Handle Spindle TurningsPlotting The Shape Tenon Sizing CutsUsing a Template Diameter Board Using a Template and a Diameter BoardDuplicate Turnings Use of PatternsFaceplate & Chuck Turnings Long SpindlesPlanning The Work Planning Various CutsDeep Recesses How To Make Fancy Faceplate TurningsPreparing a Plug Chuck Rechucking Turning CylindersTurned Boxes Turning a RingLid Lids Body Backing Block Face Plate Sanding, Buffing And Polishing Using The Lathe To Sand TurningsCoves Wood Fibers SandpaperMaintenance Wiring DiagramRecommended Accessories MaintenanceGeneral TroubleshootingTrouble Probable Cause Remedy LOW Voltage MotorStarting switch Burned switch con Ridgid 12 Wood Lathe Model No. WL1200LS1 Repair PartsWood Turning Lathe Model Always order by Part Number -- Not by Key Number Ridgid 12 Wood-Turning Lathe Model No. WL1200LS1Repair Parts Always order by Part Number -- Not by Key Number Description Call