RIDGID WL1200LS1 manual Headstock, Tailstock, and Tool Rest Assembly, Tube Large Tool Rest

Page 17

Headstock, Tailstock, and Tool Rest Assembly

1.Find the following:

1Tube

1Large Tool Rest

1Tailstock

2Lever Assembly

1Hex Head Screw M10 x 1.5-30

1Tool Rest Holder/Clamp Support Assembly

2Brass Shoe Locks

2.Place the tube assembly on your work- bench as shown. Always keep the squared key section straight down.

3.Slide the tube into the headstock until it stops against the squared key section. Insert hex head screw and tighten securely.

4.Slide the tool rest holder/clamp support assembly onto the middle of the tube. Assemble lever assembly as shown.

NOTE: Make sure to insert brass shoe lock before installing lever assembly.

Tube	Large Tool
	Rest
Lever
Assembly	Hex Hd Screw
	Hex Hd Screw
Tailstock	M10 x 1.5-30

Brass Shoe

Tool Rest Holder Lock

Clamp Support

Assembly

Tube Assembly

Squared Key Section

Headstock Spindle

Spindle Pulley

Tube

Hex Head

Locking Screw

in Rear of

Headstock

Squared Key

Section

Clamp Support

Headstock

End

Brass Shoe

Lock Lever

Assembly

17

Image 17

Contents +22 7851,1*/$7+ Safety Instructions For Wood Turning Lathe Table of ContentsKnow and Understand the Lathe Safety Symbols Before Using the LatheReduce the Risk of Dangerous Environment Use Recommended AccessoriesTo reduce the risk of injury from unexpected lathe movement Inspect your latheReduce the Risk of Accidental Starting Dress for safetyKeep Children Away Inspect Your WorkpieceDon’t Force Tool Before freeing jammed materialPower Supply and Motor Specifications Motor Specifications and Electrical RequirementsGeneral Electrical Connections Volt, 60 Hz. Tool InformationMotor Safety Protection Unpacking and Checking Contents Loose Parts Package Assembling Steel Legset AssemblyBoard/Side Support Holes Used for Mounting Boards and Wood Lathe to Leg SetMounting Left Side Table Top Motor Mounting Plate Right Side Table Top Left Side Mounting Right Side Table TopParticle Board Table Top Carriage Bolt M6 x Mounting Headstock Assembly Headstock Carriage Bolt M6 x Hex Head Nut HexBelt Guard Pan Head Thread Cutting Screw M5 x 0.8 x Pan ScrewM6 x Hex Head Screw Carriage Bolt Mounting the MotorHex Nut X 19 xAssembly Tube Large Tool Rest Headstock, Tailstock, and Tool Rest AssemblyAssembly Hex Hd Screw Tailstock Assembly Pan Head Screw Mounting Rear FootNut Square Flat Washer M8 x X 19 x Nut Hex M6 xHex Nut 3/4-16 Live Center Tailstock Ram Dia Wood Dowel Foot Spur and Cup Center InstallationCheck Spindle Rotation Adjusting TailstockAligning Centers ScrewHeadstock Getting To Know Your Wood LatheBed Yellow Switch Key On-off SwitchChanging Speeds Basic Lathe OperationsDiagonal Lines on Both Ends Spindle TurningWood Tool Rest Faceplate Turning Basic Lathe Operations Indexing Woodworking Chisels and How to Use Them How To Use Your Ridgid Wood LatheSix Commonly Used Chisel Types Selection Of Chisels Theory Of TurningDiameter Approach Circumference When You Can Cut, and When You Must ScrapeHow to Position Tool Rest for Circum- ference Cutting Rest Face Edge How to Position Tool Rest for Circumference ScrapingUsing The Skew Using The GougeSupport Using Toe Edge does not cut Using Heel Cutting Edge AdvancedWrong RightSpear Round Flat Point Nose Nose Using The Parting ToolUsing The Scraping Chisels Roughing Off Finish Cutting Hand PositionsMaking Standard Cuts Parting Tool Pencil Mark Pencil Skew Wrong Right Bevel Smoothing a CylinderCutting a Shoulder Cutting Beads Cutting VeesPencil Marks Cutting Coves ConcavesCutting Coves Making Long Convex CutsMaking Long Taper Cuts How To Handle Spindle TurningsPlotting The Shape Tenon Sizing CutsUsing a Template Diameter Board Using a Template and a Diameter BoardDuplicate Turnings Use of PatternsFaceplate & Chuck Turnings Long SpindlesPlanning The Work Planning Various CutsPreparing a Plug Chuck How To Make Fancy Faceplate TurningsDeep Recesses Rechucking Turning CylindersLid Lids Body Backing Block Face Plate Turning a RingTurned Boxes Sanding, Buffing And Polishing Using The Lathe To Sand TurningsCoves Wood Fibers SandpaperMaintenance Wiring DiagramRecommended Accessories MaintenanceTrouble Probable Cause Remedy TroubleshootingGeneral LOW Voltage MotorStarting switch Burned switch con Ridgid 12 Wood Lathe Model No. WL1200LS1 Repair PartsWood Turning Lathe Model Always order by Part Number -- Not by Key Number Ridgid 12 Wood-Turning Lathe Model No. WL1200LS1Repair Parts Always order by Part Number -- Not by Key Number Description Call