RIDGID manual Repair Parts, Ridgid 12 Wood Lathe Model No. WL1200LS1

Page 51

Repair Parts

RIDGID 12" Wood Lathe

Model No. WL1200LS1

Figure 1

NOTE: Any attempt to repair this motor may create a hazard unless repair is done by qualified service technician.

Repair service is available at an Authorized Service Center.

1

2

Always order by Part Number -- Not by Key Number

	Key	Part No.	Description
	No.	Part No.	Description
	No.


	1	828929	Motor
	2	830177	Cord, Motor

51

Image 51

Contents +22 7851,1*/$7+ Safety Instructions For Wood Turning Lathe Table of ContentsKnow and Understand the Lathe Safety Symbols Before Using the LatheInspect your lathe Use Recommended AccessoriesReduce the Risk of Dangerous Environment To reduce the risk of injury from unexpected lathe movementReduce the Risk of Accidental Starting Dress for safetyBefore freeing jammed material Inspect Your WorkpieceKeep Children Away Don’t Force ToolVolt, 60 Hz. Tool Information Motor Specifications and Electrical RequirementsPower Supply and Motor Specifications General Electrical ConnectionsMotor Safety Protection Unpacking and Checking Contents Loose Parts Package Assembling Steel Legset AssemblyHoles Used for Mounting Boards and Wood Lathe to Leg Set Mounting Left Side Table TopBoard/Side Support Mounting Right Side Table Top Particle Board Table Top Carriage Bolt M6 xMotor Mounting Plate Right Side Table Top Left Side Pan Head Thread Cutting Screw M5 x 0.8 x Pan Screw Assembly Headstock Carriage Bolt M6 x Hex Head Nut HexMounting Headstock Belt GuardX 19 x Mounting the MotorM6 x Hex Head Screw Carriage Bolt Hex NutAssembly Headstock, Tailstock, and Tool Rest Assembly Assembly Hex Hd Screw TailstockTube Large Tool Rest Assembly M8 x X 19 x Nut Hex M6 x Mounting Rear FootPan Head Screw Nut Square Flat WasherHex Nut 3/4-16 Live Center Tailstock Ram Dia Wood Dowel Foot Spur and Cup Center InstallationScrew Adjusting TailstockCheck Spindle Rotation Aligning CentersGetting To Know Your Wood Lathe BedHeadstock Yellow Switch Key On-off SwitchChanging Speeds Basic Lathe OperationsDiagonal Lines on Both Ends Spindle TurningWood Tool Rest Faceplate Turning Basic Lathe Operations Indexing Theory Of Turning How To Use Your Ridgid Wood LatheWoodworking Chisels and How to Use Them Six Commonly Used Chisel Types Selection Of ChiselsWhen You Can Cut, and When You Must Scrape How to Position Tool Rest for Circum- ference CuttingDiameter Approach Circumference Rest Face Edge How to Position Tool Rest for Circumference ScrapingCutting Edge AdvancedWrong Right Using The GougeUsing The Skew Support Using Toe Edge does not cut Using HeelUsing The Parting Tool Using The Scraping ChiselsSpear Round Flat Point Nose Nose Roughing Off Finish Cutting Hand PositionsMaking Standard Cuts Smoothing a Cylinder Cutting a ShoulderParting Tool Pencil Mark Pencil Skew Wrong Right Bevel Cutting Beads Cutting VeesMaking Long Convex Cuts Cutting Coves ConcavesPencil Marks Cutting CovesTenon Sizing Cuts How To Handle Spindle TurningsMaking Long Taper Cuts Plotting The ShapeUse of Patterns Using a Template and a Diameter BoardUsing a Template Diameter Board Duplicate TurningsPlanning Various Cuts Long SpindlesFaceplate & Chuck Turnings Planning The WorkHow To Make Fancy Faceplate Turnings Deep RecessesPreparing a Plug Chuck Rechucking Turning CylindersTurning a Ring Turned BoxesLid Lids Body Backing Block Face Plate Wood Fibers Sandpaper Using The Lathe To Sand TurningsSanding, Buffing And Polishing CovesMaintenance Wiring DiagramMaintenance Recommended AccessoriesTroubleshooting GeneralTrouble Probable Cause Remedy LOW Voltage MotorStarting switch Burned switch con Ridgid 12 Wood Lathe Model No. WL1200LS1 Repair PartsWood Turning Lathe Model Always order by Part Number -- Not by Key Number Ridgid 12 Wood-Turning Lathe Model No. WL1200LS1Repair Parts Always order by Part Number -- Not by Key Number Description Call