Grizzly G4003G owner manual Machine Data Sheet

Page 5

Machine Data Sheet

MACHINE DATA

SHEET

Customer Service #: (570) 546-9663 · To Order Call: (800) 523-4777 · Fax #: (800) 438-5901

MODEL G4003G

GUNSMITH'S BENCH TOP LATHE WITH STAND

Product Dimensions:
Weight	1213 lbs.
Length/Width/Height	61 x 26 x 54-1/2 in.
Foot Print (Length/Width)	57-1/2 x 14-1/2 in.
Shipping Dimensions:
Type	Wood Crate
Content	Machine
Weight	1500 lbs.
Length/Width/Height	65 x 30 x 61 in.
Electrical:
Switch	On/Off Reverse
Switch Voltage	220V
Cord Length	5-1/2 ft.
Cord Gauge	14 gauge
Recommended Breaker Size	15 amp
Plug	No
Motors:
Main
Type	TEFC Capacitor Start Induction
Horsepower	2 HP
Voltage	220V
Prewired	220V
Phase	Single
Amps	12A
Speed	1725 RPM
Cycle	60 Hz
Number Of Speeds	1
Power Transfer	Twin V-Belt to Gear
Bearings	Shielded and Lubricated for Life
Main Specifications:
Operation Info
Swing Over Bed	12 in.
Dist Between Centers	36 in.
Swing Over Cross Slide	7 in.
Swing Over Saddle	11-11/32 in.
Swing Over Gap	17 in.
Max Tool Bit Size	5/8 in.
Compound Travel	3-1/4 in.
Carriage Travel	24 in.
Cross Slide Travel	6-1/4 in.

The information contained herein is deemed accurate as of 11/12/2007 and represents our most recent product specifications.

Due to our ongoing improvement efforts, this information may not accurately describe items previously purchased.

G4003G Gunsmith's Lathe

-3-

Image 5

Contents Model G4003G Gunsmiths Lathe Page Table of Contents Contact Info IntroductionForeword Machine Data Sheet Tailstock Info Identification G4003G Gunsmiths Lathe G4003G Gunsmiths Lathe Additional Safety Instructions for Lathes Glossary of Terms Circuit Requirements 220V Single-PhaseSetup Safety SetupItems Needed for Setup UnpackingMajor Components Figure Qty InventoryLoose Components Figure Hex Wrench Set 2, 4, 5, 6, 8, 10 mm .. eaPlacement Location Clean UpSite Considerations Floor LoadBolting to Concrete Floors To assembly the cabinet baseMounting to Shop Lifting & Moving Test Run & Break-In To begin the test run & break-in procedureTo align the tailstock Tailstock SetupAdjusting for tailstock end taper Operation Operation SafetySpindle Speeds ExampleMounting Chuck Faceplate Disconnect Lathe from PowerTo install a chuck Spider CentersSpiderTo use the follow rest Steady Rest Follow RestTo use the steady rest Feed Rod Lever Feed Direction LeverGearbox Levers Feed Rate ChartInch Threading Half-Nut LeverStandard thread chart Change Gears and Metric Threading To use the chartCarriage Handwheel Carriage HandwheelsCompound Slide Handwheel Cross Slide HandwheelTailstock Controls Tool Post & HolderTailstock Handwheel Barrel Lock LeverH6095-Digital Readout DRO AccessoriesQuick Change Tool Holders MT#3 Long Nose Center Lubrication MaintenanceBasic Maintenance Slides and Ways Motor & Gearbox ServiceTroubleshooting Operation and Work Results Cross-slide Gib, see Figure GibsBearing Preload Disconnect the Lathe from the Power SourceAdjusting spindle bearings To confirm that the bearings are correctly pre- loaded Electrical box wiring G4003G Gunsmiths Lathe Wiring-Electrical BoxG4003G Gunsmiths Lathe Motor wiring Wiring-Motor & Control PanelG4003G Gunsmiths Lathe Work light wiring Wiring-Plug, Light & Spindle SwitchG4003G Gunsmiths Lathe Components PartsGearbox Gearing Gearbox Gearing Parts List Gearbox Gearbox Shifters Parts List Quick Change System Quick Change System Parts List Apron Apron Parts List Saddle Saddle Parts List Compound Slide Tailstock Lathe Bed & Motor Base Lathe Bed, Motor & Base Parts List Feed Rod Feed Rod Parts List Machine Labels Electrical Components Steady & Follow Rest Assemblies Page Page Warranty and Returns