Grizzly G4003G owner manual Tailstock Info

Page 6

Headstock Info
Spindle Bore	1-5/8 in.
Spindle Size	3-1/4 in.
Spindle Taper	MT#5
No Of Spindle Speeds	9
Range Of Spindle Speeds	70, 200, 220, 270, 360, 600, 800, 1000, 1400 RPM
Spindle Type	D1-5 Cam Lock
Spindle Bearings	High Precision Tapered Roller
Tailstock Info
Tailstock Travel	4 in.
Tailstock Taper	MT#3
Tailstock Barrel Diameter	1-9/16 in.
Threading Info
No Of Inch Threads	40
Range Of Inch Threads	4 - 112 TPI
Range Of Longitudinal Feeds	0.0011 - 0.031 in.
No Of Longitudinal Feeds	40
No Of Cross Feeds	40
Range Of Cross Feeds	0.0004 - 0.0105 in./rev.
No Of Metric Threads	29
Range Of Metric Threads	0.2 - 4.5 mm
Dimensions
Bed Width	7-1/4 in.
Leadscrew TPI	8
Leadscrew Length	44 in.
Steady Rest Capacity	3/16 - 2 in.
Follow Rest Capacity	1/4 - 1 in.
Faceplate Size	10 in.
Leadscrew Diameter	0.870 in.
Feed Rod Diameter	0.780 in.
Floor To Center Height	46-1/4 in.
Construction
Base Construction	Cast Iron
Headstock Construction	Cast Iron
Headstock Gears Construction	Flame Hardened Steel
Bed Construction	Induction Hardened Cast Iron
Body Construction	Cast Iron
Stand Construction	Cast Iron
Paint	Epoxy
Other
Kilowatt Output	1.119
Other Specifications:
Country Of Origin	China
Warranty	1 Year
Serial Number Location	ID Label on Headstock
Assembly Time	1-1/2 hours

The information contained herein is deemed accurate as of 11/12/2007 and represents our most recent product specifications

Due to our ongoing improvement efforts, this information may not accurately describe items previously purchased.

-4-	G4003G Gunsmith's Lathe

Image 6

Contents Model G4003G Gunsmiths Lathe Page Table of Contents Introduction ForewordContact Info Machine Data Sheet Tailstock Info Identification G4003G Gunsmiths Lathe G4003G Gunsmiths Lathe Additional Safety Instructions for Lathes Glossary of Terms 220V Single-Phase Circuit RequirementsItems Needed for Setup SetupSetup Safety UnpackingLoose Components Figure InventoryMajor Components Figure Qty Hex Wrench Set 2, 4, 5, 6, 8, 10 mm .. eaSite Considerations Clean UpPlacement Location Floor LoadTo assembly the cabinet base Mounting to ShopBolting to Concrete Floors Lifting & Moving To begin the test run & break-in procedure Test Run & Break-InTailstock Setup To align the tailstockAdjusting for tailstock end taper Spindle Speeds Operation SafetyOperation ExampleDisconnect Lathe from Power Mounting Chuck FaceplateTo install a chuck CentersSpider SpiderSteady Rest Follow Rest To use the steady restTo use the follow rest Feed Direction Lever Feed Rod LeverFeed Rate Chart Gearbox LeversHalf-Nut Lever Inch ThreadingStandard thread chart To use the chart Change Gears and Metric ThreadingCompound Slide Handwheel Carriage HandwheelsCarriage Handwheel Cross Slide HandwheelTailstock Handwheel Tool Post & HolderTailstock Controls Barrel Lock LeverAccessories Quick Change Tool HoldersH6095-Digital Readout DRO MT#3 Long Nose Center Maintenance Basic MaintenanceLubrication Slides and Ways Service TroubleshootingMotor & Gearbox Operation and Work Results Gibs Cross-slide Gib, see FigureDisconnect the Lathe from the Power Source Bearing PreloadAdjusting spindle bearings To confirm that the bearings are correctly pre- loaded Wiring-Electrical Box Electrical box wiring G4003G Gunsmiths LatheG4003G Gunsmiths Lathe Wiring-Motor & Control Panel Motor wiringG4003G Gunsmiths Lathe Wiring-Plug, Light & Spindle Switch Work light wiringG4003G Gunsmiths Lathe Parts ComponentsGearbox Gearing Gearbox Gearing Parts List Gearbox Gearbox Shifters Parts List Quick Change System Quick Change System Parts List Apron Apron Parts List Saddle Saddle Parts List Compound Slide Tailstock Lathe Bed & Motor Base Lathe Bed, Motor & Base Parts List Feed Rod Feed Rod Parts List Machine Labels Electrical Components Steady & Follow Rest Assemblies Page Page Warranty and Returns