Grizzly G0694 owner manual Circuit Requirements, 220V Single-Phase Operation

Page 11

SECTION 2: CIRCUIT REQUIREMENTS

220V Single-Phase

Operation

Serious personal injury could occur if you connect the machine to power before com- pleting the setup process. DO NOT connect the machine to the power until instructed later in this manual.

Electrocution or fire could result if machine is not grounded and installed in compliance with electrical codes. Compliance MUST be verified by a qualified electrician!

Full Load Amperage Draw

This machine draws the following amps under maximum load:

Amp Draw

9 Amps

Power Supply Circuit Requirements

The power supply circuit for your machine MUST be grounded and rated for the amperage given below. Never replace a circuit breaker on an exist- ing circuit with one of higher amperage without consulting a qualified electrician to ensure compli- ance with wiring codes. If you are unsure about the wiring codes in your area or you plan to connect your machine to a shared circuit, con- sult a qualified electrician.

Minimum Circuit Size

15 Amps

Power Connection Device

The type of plug required to connect your machine to power depends on the type of service you cur- rently have or plan to install. We recommend using the plug shown in Figure 2.

Figure 2. NEMA 6-15 plug and receptacle.

Extension Cords

Using extension cords may reduce the life of the motor. Instead, place the machine near a power source. If you must use an extension cord:

Use at least a 14 gauge cord that does not exceed 50 feet in length!

The extension cord must also have a ground wire and plug pin.

A qualified electrician MUST size cords over 50 feet long to prevent motor damage.

Model G0694 (Mfg. Since 1/09)

-9-

Image 11
Contents Model G0694 Page Table of Contents Machine Description IntroductionManual Accuracy Contact InfoIdentification Machine Data Sheet Tailstock Information Safety Instructions for Machinery SafetyKeep CHILDREN/VISITORS Away Preventing Thrown Workpiece Additional Safety for Wood LathesCircuit Requirements 220V Single-Phase OperationDescription Qty SetupNeeded for Setup UnpackingInventory Figure Qty InventoryBefore cleaning, gather the following CleanupSite Considerations Moving & Placing Lathe Bolting to Concrete Floors Mounting to Shop FloorStop Button Test RunPage Basic Controls OperationsStock Inspection Requirements Operation OverviewTo position and lock the tailstock in position TailstockInboard Tool Rest Positioning Inboard Tool Rest on BedwayTo use the outboard tool rest Adjusting Tool Rest HeightOutboard Tool Rest Tools Needed Qty Installing/Removing Headstock CenterInstalling Headstock Center Removing Headstock CenterTo remove the center from the tailstock quill Installing/Removing Tailstock CenterTo install the center into the tailstock quill Removing Faceplate or Handwheel Installing Faceplate HandwheelInstalling Faceplate or Handwheel Cutting Adjusting Spindle SpeedsFinishing WorkWindow IndexingSelecting Turning Tools Spindle Turning Setting Up for Spindle TurningPage Mounting Workpiece on Faceplate Spindle Turning Safety TipsFaceplate Turning To mount your workpiece to a backing block Using Backing BlockOutboard Turning Typical sanding operation Sandpaper Workpiece Sanding/FinishingAccessories G9863-8-PC HSS Lathe Chisel Set Model H6542 Robert Sorby 8-PC SetLathe Bed MaintenanceCleaning ScheduleLubricating Spindle Bearings Tailstock General LubricationTo lubricate the bottom of the tool rest hold- er Inboard Tool RestOutboard Tool Rest Spur and Live CentersMotor & Electrical ServiceTroubleshooting Wood Lathe Operation Tensioning Belt Belt AdjustmentChecking Belt To remove the existing belt and install a new belt Changing Belt Bearing ServiceRemoving speed sensor screws Model G0694 Mfg. Since 1/09 Packing outboard roller bearing with Grease Speed Sensor Model G0694 Mfg. Since 1/09 Wiring Safety Instructions WiringSwitch Button Junction Block Wiring DiagramElectrical Components Control panel wiringParts Description Lathe Parts ListStand Breakdown Stand Parts List Labels & Cosmetics Breakdown Comments Warranty CardBOX BELLINGHAM, WA Grizzly INDUSTRIAL, INCWarranty and Returns Warranty and ReturnsOrder Hours a DAY