Grizzly G0694 owner manual Labels & Cosmetics Breakdown

Page 56

Labels & Cosmetics Breakdown

211

203

204

205

212

206

207

201

202

210

209

208

REF	PART #	DESCRIPTION

201	P0694201	G0694 MACHINE ID LABEL
202	P0694202	G0694 MODEL # LABEL
203	PLABEL-56	FACE SHIELD RESPIRATOR LABEL
204	PLABEL-55	ENTANGLEMENT LABEL
205	PLABEL-12A	READ MANUAL LABEL
206	PLABEL-14A	ELECTRICITY LABEL

REF	PART #	DESCRIPTION

207	PLABEL-63	DISCONNECT POWER LABEL
208	G8588	GRIZZLY NAMEPLATE-SMALL
209	PPAINT-1	"GRIZZLY GREEN" PAINT
210	PPAINT-11	"GRIZZLY PUTTY" PAINT
211	P0694211	BELT POSITION LABEL
212	P0694212	CRUSHING HAZARD LABEL

Safety labels warn about machine hazards and ways to prevent injury. The owner of this machine MUST maintain the original location and readability of the labels on the machine. If any label is removed or becomes unreadable, REPLACE that label before using the machine again. Contact Grizzly at (800) 523-4777 or www.grizzly.com to order new labels.

-54-	Model G0694 (Mfg. Since 1/09)

Image 56

Contents Model G0694 Page Table of Contents Introduction Manual AccuracyContact Info Machine DescriptionIdentification Machine Data Sheet Tailstock Information Safety Safety Instructions for MachineryKeep CHILDREN/VISITORS Away Additional Safety for Wood Lathes Preventing Thrown Workpiece220V Single-Phase Operation Circuit RequirementsSetup Needed for SetupUnpacking Description QtyInventory Inventory Figure QtyCleanup Before cleaning, gather the followingSite Considerations Moving & Placing Lathe Mounting to Shop Floor Bolting to Concrete FloorsTest Run Stop ButtonPage Operations Basic ControlsOperation Overview Stock Inspection RequirementsTailstock Inboard Tool RestPositioning Inboard Tool Rest on Bedway To position and lock the tailstock in positionTo use the outboard tool rest Adjusting Tool Rest HeightOutboard Tool Rest Installing/Removing Headstock Center Installing Headstock CenterRemoving Headstock Center Tools Needed QtyTo remove the center from the tailstock quill Installing/Removing Tailstock CenterTo install the center into the tailstock quill Removing Faceplate or Handwheel Installing Faceplate HandwheelInstalling Faceplate or Handwheel Adjusting Spindle Speeds FinishingWork CuttingIndexing WindowSelecting Turning Tools Setting Up for Spindle Turning Spindle TurningPage Mounting Workpiece on Faceplate Spindle Turning Safety TipsFaceplate Turning To mount your workpiece to a backing block Using Backing BlockOutboard Turning Sanding/Finishing Typical sanding operation Sandpaper WorkpieceAccessories Model H6542 Robert Sorby 8-PC Set G9863-8-PC HSS Lathe Chisel SetMaintenance CleaningSchedule Lathe BedLubricating Spindle Bearings General Lubrication TailstockInboard Tool Rest Outboard Tool RestSpur and Live Centers To lubricate the bottom of the tool rest hold- erMotor & Electrical ServiceTroubleshooting Wood Lathe Operation Tensioning Belt Belt AdjustmentChecking Belt Changing Belt Bearing Service To remove the existing belt and install a new beltRemoving speed sensor screws Model G0694 Mfg. Since 1/09 Packing outboard roller bearing with Grease Speed Sensor Model G0694 Mfg. Since 1/09 Wiring Wiring Safety InstructionsWiring Diagram Switch Button Junction BlockControl panel wiring Electrical ComponentsParts Lathe Parts List DescriptionStand Breakdown Stand Parts List Labels & Cosmetics Breakdown Warranty Card CommentsGrizzly INDUSTRIAL, INC BOX BELLINGHAM, WAWarranty and Returns Warranty and ReturnsOrder Hours a DAY