Grizzly G0694 owner manual Table of Contents

Page 3

Table of Contents

INTRODUCTION	2
Manual Accuracy	2
Contact Info	2
Machine Description	2
Identification	3
Machine Data Sheet	4
SECTION 1: SAFETY	6
Safety Instructions for Machinery	6
Additional Safety for Wood Lathes	8
SECTION 2: CIRCUIT REQUIREMENTS	9
220V Single-Phase Operation	9
SECTION 3: SETUP	10
Needed for Setup	10
Unpacking	10
Inventory	11
Cleanup	12
Site Considerations	13
Moving & Placing Lathe	14
Mounting to Shop Floor	15
Test Run	16
SECTION 4: OPERATIONS	18
Basic Controls	18
Operation Overview	19
Stock Inspection & Requirements	19
Tailstock	20
Inboard Tool Rest	20
Outboard Tool Rest	21
Installing/Removing Headstock Center	22
Installing/Removing Tailstock Center	23
Installing Faceplate/Handwheel	24
Adjusting Spindle Speeds	25
Indexing	26
Selecting Turning Tools	27
Spindle Turning	28
Faceplate Turning	30
Outboard Turning	31
Sanding/Finishing	32

SECTION 5: ACCESSORIES	33
SECTION 6: MAINTENANCE	35
Schedule	35
Cleaning	35
Lathe Bed	35
Spindle Bearing Lubrication	35
General Lubrication	37
SECTION 7: SERVICE	39
Troubleshooting	39
Belt Adjustment	41
Changing Belt/Bearing Service	42
SECTION 8: WIRING	47
Wiring Safety Instructions	47
Wiring Diagram	48
Electrical Components	49
SECTION 9: PARTS	50
Lathe	50
Stand	52
Stand Parts List	53
Labels & Cosmetics	54
WARRANTY AND RETURNS	57

Image 3

Contents Model G0694 Page Table of Contents Machine Description IntroductionManual Accuracy Contact InfoIdentification Machine Data Sheet Tailstock Information Safety Instructions for Machinery SafetyKeep CHILDREN/VISITORS Away Preventing Thrown Workpiece Additional Safety for Wood LathesCircuit Requirements 220V Single-Phase OperationDescription Qty SetupNeeded for Setup UnpackingInventory Figure Qty InventoryBefore cleaning, gather the following CleanupSite Considerations Moving & Placing Lathe Bolting to Concrete Floors Mounting to Shop FloorStop Button Test RunPage Basic Controls OperationsStock Inspection Requirements Operation OverviewTo position and lock the tailstock in position TailstockInboard Tool Rest Positioning Inboard Tool Rest on BedwayAdjusting Tool Rest Height Outboard Tool RestTo use the outboard tool rest Tools Needed Qty Installing/Removing Headstock CenterInstalling Headstock Center Removing Headstock CenterInstalling/Removing Tailstock Center To install the center into the tailstock quillTo remove the center from the tailstock quill Installing Faceplate Handwheel Installing Faceplate or HandwheelRemoving Faceplate or Handwheel Cutting Adjusting Spindle SpeedsFinishing WorkWindow IndexingSelecting Turning Tools Spindle Turning Setting Up for Spindle TurningPage Spindle Turning Safety Tips Faceplate TurningMounting Workpiece on Faceplate Using Backing Block Outboard TurningTo mount your workpiece to a backing block Typical sanding operation Sandpaper Workpiece Sanding/FinishingAccessories G9863-8-PC HSS Lathe Chisel Set Model H6542 Robert Sorby 8-PC SetLathe Bed MaintenanceCleaning ScheduleLubricating Spindle Bearings Tailstock General LubricationTo lubricate the bottom of the tool rest hold- er Inboard Tool RestOutboard Tool Rest Spur and Live CentersService TroubleshootingMotor & Electrical Wood Lathe Operation Belt Adjustment Checking BeltTensioning Belt To remove the existing belt and install a new belt Changing Belt Bearing ServiceRemoving speed sensor screws Model G0694 Mfg. Since 1/09 Packing outboard roller bearing with Grease Speed Sensor Model G0694 Mfg. Since 1/09 Wiring Safety Instructions WiringSwitch Button Junction Block Wiring DiagramElectrical Components Control panel wiringParts Description Lathe Parts ListStand Breakdown Stand Parts List Labels & Cosmetics Breakdown Comments Warranty CardBOX BELLINGHAM, WA Grizzly INDUSTRIAL, INCWarranty and Returns Warranty and ReturnsOrder Hours a DAY