Jet Tools JWL-1442VS operating instructions Adjustments, Adjusting the Clamping Mechanism

Page 19

Adjustments

Adjusting the Clamping Mechanism

The clamps are pre-set at the factory and should not need any adjustment. However, if adjustment is needed, remove the stud (A, Fig. 23). Loosen the locking handle and slide the headstock, tailstock or tool rest to the edge of the bed and slightly turn the hex nut (B, Fig. 23). Slide back into position and test the handle to make sure it securely locks.

Changing the Belt and Bearings

Changing belt and bearings can be a difficult task, and should be performed by a JET authorized repair station. Remove headstock and take into a repair station for servicing.

1.Place the belt in its highest speed range. Do not change speeds while changing the belt or bearings.

2.Remove the belt cover, and remove the belt from the lower pulley, see Figure 24.

3.Loosen the two setscrews in the handwheel enough to unthread the handwheel (C, Fig. 24).

4.Loosen the socket head cap screw enough to unthread the clamping nut (D, Fig. 24).

5.Remove one e-ring (E, Fig. 24) from spindle.

6.Loosen the two setscrews in the right hand pulley (F, Fig. 24).

7.Use a wood dowel, or aluminum stock to knock the spindle towards the tailstock. Use a material that is softer than the spindle so you do not mushroom the end of the spindle. Go only far enough to remove the right hand pulley and belt from spindle, see Figure 25 when changing the belt. Note: Mark the key way on the pulley for easy reference when reassembling.

8.Now you can replace the belt or bearings. There are three bearings #6, 9 and 43 that can be seen in the “Headstock Assembly,” on page 25.

9.To reassemble reverse the procedure. Note: Key way alignment is critical for installment and proper operation. Do not force the pulley. When reinstalling clamping nut thread it on to the spindle until its snug. Then back off slightly and tighten the socket head cap screw.

Figure 23

Figure 24

Figure 25

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Part No. M-708358 Walter Meier Manufacturing IncMore Information Warranty and ServiceTable of Contents Page Speed Recommendations Introduction Specifications Assembly Shipping ContentsStand Shelf Tool RestVolt Operation Grounding InstructionsHeadstock Spindle Lock G, Fig Controls and FeaturesHeadstock Lock Handle E, Fig Headstock Indexing Pin F, FigTailstock Lock Handle P, Fig Headstock Faceplate K, FigHeadstock Spur Center L, Fig Headstock Indexing Hole M, FigMounting Workpiece Between Centers Lathe ToolsStock Selection OperationsRoughing Out Cuts BeadsParting CovesFace Plate and Bowl Turning Sanding and FinishingMounting Stock Distortion Face Plate or ChuckWood Selection Checks and CracksTo Shape the Outside of a Bowl Sanding and Finishing a Bowl To Shape the Interior of a BowlAdjusting the Clamping Mechanism AdjustmentsChanging the Belt and Bearings Safety Guard Optional AccessoriesTool Basket Ordering Replacement Parts TroubleshootingParts Index No Description Size Qty Bed Assembly Parts ListIndex No. Part No Description Size Qty Headstock Assembly Parts ListTS-0081031 Hex Head Bolt 16-18 x 3/4 TS-0720081 Headstock Assembly Stand Assembly Basket Assembly Safety Guard AssemblyWiring Diagram Appendix Indexer Positions How to use the chartPage Page New Sanford Road LaVergne, Tennessee
Related manuals
Manual 32 pages 6.3 Kb

JWL-1442VS specifications

The Jet Tools JWL-1442VS is a robust wood lathe designed for both novice and experienced woodturners. Known for its versatility and reliability, it has become a go-to choice for many who seek to create intricate designs. This lathe combines advanced technology with user-friendly features, making it suitable for crafting everything from simple spindle work to complex bowls and detailed ornaments.

One of the standout features of the JWL-1442VS is its variable speed control, allowing users to adjust the speed from 40 to 3200 RPM. This range provides the flexibility needed for different turning projects, ensuring optimal performance for both roughing and finishing tasks. The digital readout on the control panel displays the current speed, making it easy for users to monitor and adjust as needed.

Another notable characteristic is its 14-inch swing over the bed and 42 inches between centers. This generous capacity enables woodturners to work with larger pieces of stock while maintaining precision and stability. The sturdy cast iron construction of the lathe adds to its durability, absorbing vibrations and providing a solid base for safe operation.

The JWL-1442VS also features a sliding headstock, which enhances accessibility and allows for outboard turning. This capability is particularly beneficial when working on larger bowls or wide pieces, as it provides additional room and maneuverability. The tailstock features a convenient lockable design that promotes secure positioning and easy adjustments.

In addition to its mechanical advantages, this wood lathe is equipped with Jet's innovative quick-release spindle lock. This feature enables users to quickly change out chucks and accessories, reducing downtime and increasing productivity. The machine’s ease of use is complemented by its user-friendly controls and intuitive design.

Safety is also a priority with the JWL-1442VS, featuring a built-in safety switch that helps prevent accidental starts. This attention to safety ensures that woodturners can focus on their craft without unnecessary concerns.

In conclusion, the Jet Tools JWL-1442VS is a versatile and powerful wood lathe that caters to a wide range of turning needs. With its advanced variable speed control, robust construction, and thoughtful features, it stands out as an excellent choice for anyone looking to elevate their woodturning experience. Whether you are a beginner or a seasoned pro, the JWL-1442VS promises to deliver performance and reliability for countless turning projects.
Top Page Image Contents