Jet Tools JBTS-10MJS Handwheel Handle, Installing the Blade, Removing the Blade

Page 14

Handwheel Handle

Thread the handwheel handle (DD, Fig. 10) into the handwheel hole (A. Fig. 10), and then tighten the nut against the handwheel with a 10 mm wrench.

Installing the Blade

To avoid injury from an accidental start, make sure the switch is in the OFF position and the plug is disconnected from the power source outlet.

Referring to Figure 11:

1.Remove the table insert (A).

2.Place the blade onto the arbor with the blade teeth pointing forward to the front of the saw.

3.Make sure the blade fits flush against the inner flange.

4.Clean the outer blade flange (H) and install it onto the arbor and against the blade.

5.Thread the arbor nut onto the arbor, making sure the flat side of the nut is against the blade, then hand-tighten.

6.Pull the arbor locking lever (G) toward the front of the machine while spinning the blade by hand until the latch locks into place and the blade will no longer turn.

7.Place the wrench (E) on the arbor nut and turn clockwise (toward the rear of the saw table).

8.Lower the blade to the down position. Replace the table insert (A) and the blade guard.

Important: Do not operate this saw until the blade and blade guard splitter are aligned and in working order.

Removing the Blade

To avoid injury from an accidental start, make sure the switch is in the OFF position and the plug is disconnected from the power source outlet.

Referring To Figure 11:

1.Remove the table insert (A) and raise the blade to the maximum height by turning the blade elevation handwheel clockwise.

2.Remove blade guard.

3.Adjust the blade to the 90° vertical position by unlocking the blade tilting lock knob and turning the bevel tilting handwheel counterclockwise, and then lock into position.

4.Pull the arbor locking lever (G) toward the front

Figure 10

Figure 11

of the tool while spinning the blade by hand until the latch locks into place and the blade will no longer turn.

5.Place the blade wrench (E) on the arbor nut (J).

6.Loosen and remove the arbor nut and the flange by pulling the wrench towards the front of the machine.

7.Then remove the blade (F). Clean but do not remove the inner blade flange before reassembling the blade.

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Benchtop Series Model No. JBTS-10MJS Walter Meier Manufacturing IncWarranty and Service More InformationTable of Contents Page Page Table Saw Safety Specifications Definitions and TerminologyVolt Operation Only ElectricalGrounding Instructions Extension CordsFeatures FeaturesShipping Contents Hardware HardwareAttaching Saw to Stand AssemblyStand Mounting the Saw to Work Surface Rear Table ExtensionRemoving the Blade Installing the BladeHandwheel Handle Blade Guard Assembly Splitter riving knife installation FigureRip fence and miter gauge Installing the Push-stick StorageStorage Blade wrenchAdjusting the Table Insert AdjustmentsSetting up the Stand Folding the StandAligning the Blade Guard Splitter Blade Tilt Pointer 45 Positive Stop AdjustmentAdjusting the Positive Stop StopAdditional Blade Adjustments Blade Parallel to the Miter SlotAdjusting the Miter Gauge Rip Fence AdjustmentAdjusting the Locking Lever Rip Fence IndicatorRear Table Extension Adjustment Table Extension Scale PointerOperation Basic Saw OperationsCutting Operations USE the TWO AT the Same TimeRipping Small Pieces Bevel Crosscutting 0~45 Blade Level & 90 Miter AngleMitering 0~45 Miter Angle Using the Wood Facing on the Rip FenceInterfere with the cut if used on the left side groove Dado CutsPage Lubrication MaintenanceBlade Raising and Tilting Mechanism Push Stick Construction Probable Cause Remedy TroubleshootingTrouble Table Saw Ordering Replacement PartsParts Index No Description Size QtyIndex No. Part No Description Size Qty JBTS10MJS-49JBTS10MJS-105 JBTS10MJS-162 JBTS10MJS-224 Table Saw Page Mobile Stand JBTS10MJS-658 Wiring Diagram
Top Page Image Contents