Jet Tools JBTS-10MJS Blade Guard Assembly, Splitter riving knife installation Figure

Page 15

Blade Guard Assembly

To avoid injury from an accidental start, make sure the switch is in the OFF position and the plug is disconnected from the power source outlet.

●When installing the blade guard, cover the blade teeth with a piece of folded cardboard to protect yourself from possible injury.

Splitter (riving knife) installation (Figure 12)

1.Remove the table insert.

2.Raise the blade arbor to the maximum height and set the bevel angle to 0°.

3.Install the splitter (C) onto the splitter bracket, fitting the curved slot on the splitter over the bracket pins.

4.Install the splitter plate (CC), followed by the flat washer (BB) and lock knob (AA). Tighten the lock knob, leaving enough slack to manually adjust the splitter (C).

5.Raise the splitter (C) as high as it will go, then tighten the lock knob (AA) to secure the splitter in this position.

Kickback pawl installation (Figure 12a)

6.Place the lock lever (B1) on the kickback pawl assembly (B) in the unlock position.

7.Install the kickback pawl (B) onto the splitter.

The flat sides of the mounting pin on the kickback pawls should pass though the mounting slot (C1) on the splitter (C).

Note: Make sure the “anti-kick back pawls do not get caught between the insert and the guard, but rest on top of the insert.

8.Press firmly down on the kickback pawl to ensure that it is properly seated on the splitter, then place the lock lever (B1) in the lock position.

Blade guard installation (Figure 12a)

9.Slide the lock lever (A1) on the blade guard (A) up and hold..

10.Place the blade guard (A) on the splitter (C), meshing the pin (A2) on the blade guard with the slot (C2) on the splitter.

11.Push the blade guard assembly down firmly on the splitter; then release the lock lever (A1).

12.Lift up on the blade guard assembly (A) to confirm that it is firmly secured to the splitter (C).

15

Figure 12

Figure 12a

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Walter Meier Manufacturing Inc Benchtop Series Model No. JBTS-10MJSMore Information Warranty and ServiceTable of Contents Page Page Table Saw Safety Definitions and Terminology SpecificationsExtension Cords ElectricalGrounding Instructions Volt Operation OnlyFeatures FeaturesShipping Contents Hardware HardwareAssembly StandAttaching Saw to Stand Rear Table Extension Mounting the Saw to Work SurfaceInstalling the Blade Handwheel HandleRemoving the Blade Splitter riving knife installation Figure Blade Guard AssemblyBlade wrench Installing the Push-stick StorageStorage Rip fence and miter gaugeFolding the Stand AdjustmentsSetting up the Stand Adjusting the Table InsertAligning the Blade Guard Splitter Stop 45 Positive Stop AdjustmentAdjusting the Positive Stop Blade Tilt PointerBlade Parallel to the Miter Slot Additional Blade AdjustmentsRip Fence Adjustment Adjusting the Miter GaugeTable Extension Scale Pointer Rip Fence IndicatorRear Table Extension Adjustment Adjusting the Locking LeverBasic Saw Operations OperationUSE the TWO AT the Same Time Cutting OperationsBevel Crosscutting 0~45 Blade Level & 90 Miter Angle Ripping Small PiecesDado Cuts Using the Wood Facing on the Rip FenceInterfere with the cut if used on the left side groove Mitering 0~45 Miter AnglePage Maintenance Blade Raising and Tilting MechanismLubrication Push Stick Construction Troubleshooting TroubleProbable Cause Remedy Index No Description Size Qty Ordering Replacement PartsParts Table SawJBTS10MJS-49 Index No. Part No Description Size QtyJBTS10MJS-105 JBTS10MJS-162 JBTS10MJS-224 Table Saw Page Mobile Stand JBTS10MJS-658 Wiring Diagram
Top Page Image Contents