Jet Tools JWTS-10 operating instructions Unpacking and Cleanup, Stand Assembly

Page 11

Assembly

Read and understand all assembly instructions before attempting assembly! Failure to comply may cause serious injury!

Unpacking and Cleanup

1.Remove all contents from the shipping carton. Keep the saw table upside down (Figure 1) and place on a two-by-four or similar piece of wood under the rear of the saw. This will help when picking up the table again. Do not discard the carton of packing material until the saw is assembled and is running satisfactorily.

2.Inspect the contents for shipping damage. Report damage, if any, to your distributor.

3.Compare the contents of the shipping carton with the contents list in this manual. Report shortages, if any, to your distributor.

Figure 1

Stand Assembly

Refer to Figure 2.

Tool required – 12mm wrench

Mounting Hardware – the stand (excluding wheels) is assembled using 24 each of the following: M8x16 carriage bolts (D), M8 flat washers (E), and M8 hex nuts (F).

The legs consist of one left front leg, one left rear leg and two right legs. The left legs contain the wheel mounting brackets and are not interchange- able. The right legs are interchangeable. Refer to Figure 2 for identification and orientation.

1.Assemble the front left and rear left legs (A, B) to a long top plate (C) using the mounting hardware listed above. Hand-tighten only at this time. The long top plates have no cutouts.

Note: For entire assembly place plates inside legs.

2.Assemble the right legs (G1, G2) to the remaining long top plate (C) in the same manner.

3.Assemble the short top plate with the JET logo

(H)to the front stand legs (A, G1) using the same combination of hardware as used to attach the long top plates. Hand-tighten the hardware only at this time.

4.Assemble the remaining short top plate (J) to the rear stand legs (B, G2) in the same manner.

5.Assemble two long support plates (K) to the inside of the left stand legs (A, B) and right stand legs (G1, G2) respectively with the same hardware. Hand-tighten only at this time.

Note: The long support plates have no cutouts.

Figure 2

6.Assemble two short support plates (L) to the

inside of the front stand legs (A, G1) and rear stand legs (B, G2) respectively with the same hardware. Hand-tighten only at this time.

Note: The short support plates have cutouts.

7.Assemble two wheels (M) to the left legs with two 3/8”-16 x 2.5” hex cap screws (N) and two 3/8”-16 nylon insert lock nuts (O) and tighten with two 13mm wrenches.

8.Place two wheel lock knobs (P) on the brackets above the wheels.

9.Attach wheel pad assemblies to the right legs (no wheels), each assembly consisting of one threaded wheel pad (Q), two 5/16" hex nuts (R) and two M8 flat washers (S).

11

Image 11
Contents Table Saw Warranty and Service Table of Contents Page Error! Objects cannot be created from editing field codes Protection Tips from Kickback Kickback PreventionJWTS-10 Features SpecificationsDefinitions And Terminology Shipping Contents Additional Tools Required Tools Included for AssemblyHardware Stand Assembly AssemblyUnpacking and Cleanup Blade Tilt Pointer Assembling the Saw to the StandRear Guide Rail HandwheelsExtension Wings Support Rod Front Guide RailBlade Guard and Splitter Switch BracketExtension Wing Adjustment Aligning the Blade Guard and Splitter Installing/Replacing the BladeRip Fence Table InsertOperation Miter GaugeExtension Cord Recommendations Grounding InstructionsElectrical Connections Blade Raising and Tilt Mechanism AdjustmentsAdjusting 45º and 90º Positive Stops Table Saws OperationsRip Sawing Resawing Bevel and Miter Operations Align-a-ripFeather Board Safety DevicesPush Stick & Push Block Filler PieceMiscellaneous MaintenanceCleaning LubricationSymptom Possible Cause Correction TroubleshootingParts JWTS-10 Table and Cabinet Parts ListJWTS-10 Table and Cabinet Exploded View Motor and Trunnion Assembly Parts List JWTS10-HP Motor and Trunnion Assembly Exploded View JWTS10-FA Fence and Rail Parts ListFence and Rail Exploded View Stand Assembly Parts List and Exploded View Wiring Diagram Electrical SchematicOrdering Replacement Parts Page WMH Tool Group