Delta BS150LS instruction manual Adjusting Upper Blade Guides and Blade Support Bearing

Page 14

ADJUSTING UPPER BLADE GUIDES AND BLADE SUPPORT BEARING

IMPORTANT: BOTH THE UPPER AND LOWER BLADE GUIDES MUST BE PROPERLY ADJUSTED TO PREVENT THE BLADE FROM TWISTING DURING OPERATION.

DISCONNECT MACHINE FROM POWER SOURCE.

UPPER BLADE GUARD (B) FIG. 27 IS SHOWN REMOVED FOR CLARITY. ALWAYS MAKE SURE THE UPPER BLADE GUARD IS INSTALLED AND PROPERLY ADJUSTED BEFORE OPERATING THE BAND SAW.

1.Loosen the two screws (C) Fig. 27, and adjust the blade guides (D) as close as possible to the sides of the saw blade, being careful not to pinch the blade. Tighten the two screws (C).

2.Loosen screw (E) Fig. 27, and move the guide bracket (F) in or out until the front edge of the guides (D) are just behind the “gullets” of the blade teeth. Tighten screw (E).

3.The upper blade support thrust bearing (G) Fig. 27 prevents the saw blade from being pushed back too far when cutting. The support bearing (G) should be adjusted approximately 1/32" behind the blade. The blade should also overlap the outside diameter of the ball bearing by approximately 1/8". To adjust:

4.Loosen screw (H) Fig. 28, and slide support bearing

(G) in or out until it is approximately 1/32" behind the saw blade.

5.The upper blade support bearing (G) Fig. 27, is set on an eccentric shaft. To change position of bearing (G), use a straight screwdriver, rotate shaft (J) Fig. 28, until the blade properly overlaps the support bearing. Then tighten screw (H).

GH

FE

B

C

DC

Fig. 27

J

H

Fig. 28

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Band Saw Important Safety Instructions Safety Guidelines DefinitionsGeneral Safety Rules Failure to Follow These Rules MAY Result in Serious Injury Stay ALERT, Watch What YOU are DOING,Motor Specifications Additional Safety Rules for Band SawsPower Connections Grounding Instructions Extension CordsFunctional Description Unpacking and CleaningCarton Contents Band SAW Assembly Parts Band SAW to Stand Assembly AssemblyStand Assembly Assembling Table to Machine Page Attaching Lamp to Machine StopsNever Open the Door When the Machine is Running Operating Controls and AdjustmentsLocking Switch in the OFF Position Starting and Stopping SAWDisconnect Machine from Power Source Adjusting Blade TensionAdjusting Upper Blade Guide Assembly Tracking the BladeAdjusting Upper Blade Guides and Blade Support Bearing Adjusting Lower Blade Guides and Blade Support Bearing Tilting the TableAdjusting the Table Positive Stops Carefully Turn the Blade Inside OUT Changing BladesDust Port Using the Band SAW Cutting CurvesPage Troubleshooting Guide Probable Cause RemedyTrouble Blade will not Track Band SAW Blades Page Maintenance AccessoriesCanadian PORTER-CABLE Delta Service Centers

BS150LS specifications

The Delta BS150LS is a highly regarded bandsaw that is designed to meet the demands of both professional woodworkers and hobbyists alike. Known for its robust construction and precision, this machine stands out in the market for its blend of power and versatility.

One of the main features of the Delta BS150LS is its powerful motor, which delivers ample cutting strength to handle a variety of materials, including hardwoods, softwoods, and even some non-ferrous metals. The motor has a horsepower rating that allows for smooth operation and ease of cutting without the need for excessive strain. This reliability in its operation makes it suitable for both intricate and heavy-duty cutting tasks.

Another notable characteristic of the BS150LS is its adequately sized cutting capacity. With a spacious table and substantial throat depth, users can tackle large workpieces with ease. The table itself can be adjusted to different angles, allowing for bevel cuts and providing enhanced flexibility for complex projects.

In terms of safety and convenience, the Delta BS150LS is equipped with features such as a blade guard and a quick-release tension lever. This enhances user safety while ensuring minimal downtime when changing blades. The machine is also designed with an integrated dust collection port, which helps maintain a cleaner workspace by minimizing sawdust accumulation.

The BS150LS incorporates advanced technology, including a precision ground cast iron table that provides a stable surface for accurate cutting. This is complemented by a robust frame that reduces vibration, thus enhancing the quality of the cuts and making the user experience smoother. Additionally, the bandsaw utilizes a well-engineered tracking system that ensures the blade remains aligned during operation, resulting in cleaner and more precise cuts.

Overall, the Delta BS150LS represents a perfect combination of power, precision, and safety features. It's ideal for users looking to elevate their woodworking capabilities, whether in a professional workshop or a home garage. With its reliable performance and versatile features, the BS150LS is a valuable addition to any woodworker’s toolkit.
Top Page Image Contents