Delta BS150LS Adjusting Lower Blade Guides and Blade Support Bearing, Tilting the Table

Page 15

ADJUSTING LOWER BLADE GUIDES AND BLADE SUPPORT BEARING

G D

E

The lower blade guides and blade support bearing should be adjusted at the same time as the upper guides and support bearings as follows:

A

F

C

DISCONNECT MACHINE FROM POWER

SOURCE.

1.Loosen two screws (A) Fig. 29, and move guides (B) as close as possible to the sides of the blade. Be careful not to pinch the blade. Tighten the two screws (A). NOTE: In Fig. 29, the table has been removed for clarity.

2.The front edge of the blade guides (B) Fig. 29 should be adjusted so they are just behind the “gullets” of the blade teeth. Loosen screw (C), and move the assembly

(D) in or out as necessary. Tighten screw (C).

3.The lower blade support thrust bearing (E) Fig. 29 prevents the saw blade from being pushed back too far during cutting. The support bearing should be adjusted approximately 1/32" behind the blade. Loosen screw (F) Fig. 29, and move the bearing shaft (G) in or out as necessary. Tighten screw (F).

4.The lower blade support bearing (E) Fig. 29 should also be adjusted so that the blade overlaps the outside diameter of the ball bearing by approximately 1/8". The blade support bearing (E) is set on an eccentric shaft.To change the position of the bearing (E), loosen the screw

(F) Fig. 29 and rotate the shaft (G) Fig 30 until the blade properly overlaps the support bearing. Tighten screw (F) Fig. 29.

TILTING THE TABLE

The table can be tilted 45 degrees to the right. To tilt the table, loosen lock handle (A) Fig. 31 and turn knob (B) clockwise until desired angle is established. Then tighten lock handle (A). NOTE: The table lock handle (A) can be repositioned by pulling out on the handle and repositioning it on the nut located underneath the hub of the handle. A scale (C) and pointer (D) are provided to indicate the degree of tilt.

B

A

Fig. 29

G

Fig. 30

C

D

B

A

Fig. 31

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Band Saw Safety Guidelines Definitions General Safety RulesImportant Safety Instructions Stay ALERT, Watch What YOU are DOING, Failure to Follow These Rules MAY Result in Serious InjuryAdditional Safety Rules for Band Saws Power ConnectionsMotor Specifications Extension Cords Grounding InstructionsUnpacking and Cleaning Carton ContentsFunctional Description Band SAW Assembly Parts Assembly Stand AssemblyBand SAW to Stand Assembly Assembling Table to Machine Page Stops Attaching Lamp to MachineStarting and Stopping SAW Operating Controls and AdjustmentsLocking Switch in the OFF Position Never Open the Door When the Machine is RunningTracking the Blade Adjusting Blade TensionAdjusting Upper Blade Guide Assembly Disconnect Machine from Power SourceAdjusting Upper Blade Guides and Blade Support Bearing Tilting the Table Adjusting Lower Blade Guides and Blade Support BearingAdjusting the Table Positive Stops Changing Blades Dust PortCarefully Turn the Blade Inside OUT Cutting Curves Using the Band SAWPage Probable Cause Remedy Troubleshooting GuideTrouble Blade will not Track Band SAW Blades Page Accessories MaintenanceCanadian PORTER-CABLE Delta Service Centers

BS150LS specifications

The Delta BS150LS is a highly regarded bandsaw that is designed to meet the demands of both professional woodworkers and hobbyists alike. Known for its robust construction and precision, this machine stands out in the market for its blend of power and versatility.

One of the main features of the Delta BS150LS is its powerful motor, which delivers ample cutting strength to handle a variety of materials, including hardwoods, softwoods, and even some non-ferrous metals. The motor has a horsepower rating that allows for smooth operation and ease of cutting without the need for excessive strain. This reliability in its operation makes it suitable for both intricate and heavy-duty cutting tasks.

Another notable characteristic of the BS150LS is its adequately sized cutting capacity. With a spacious table and substantial throat depth, users can tackle large workpieces with ease. The table itself can be adjusted to different angles, allowing for bevel cuts and providing enhanced flexibility for complex projects.

In terms of safety and convenience, the Delta BS150LS is equipped with features such as a blade guard and a quick-release tension lever. This enhances user safety while ensuring minimal downtime when changing blades. The machine is also designed with an integrated dust collection port, which helps maintain a cleaner workspace by minimizing sawdust accumulation.

The BS150LS incorporates advanced technology, including a precision ground cast iron table that provides a stable surface for accurate cutting. This is complemented by a robust frame that reduces vibration, thus enhancing the quality of the cuts and making the user experience smoother. Additionally, the bandsaw utilizes a well-engineered tracking system that ensures the blade remains aligned during operation, resulting in cleaner and more precise cuts.

Overall, the Delta BS150LS represents a perfect combination of power, precision, and safety features. It's ideal for users looking to elevate their woodworking capabilities, whether in a professional workshop or a home garage. With its reliable performance and versatile features, the BS150LS is a valuable addition to any woodworker’s toolkit.
Top Page Image Contents