Delta BS150LS Adjusting Blade Tension, Tracking the Blade, Adjusting Upper Blade Guide Assembly

Page 13

ADJUSTING BLADE TENSION

Blades of 1/8", 1/4", and 3/8" in width by 59-1/2" in length are available for use with your band saw. NOTE: The blade tension must be adjusted to accommodate different blade widths in order to provide proper blade tracking, cutting performance, and blade life.

DISCONNECT MACHINE FROM POWER SOURCE.

1.To install the desired blade, loosen screw (E) Fig. 25 with 5mm hex wrench provided and turn the tension knob

(A) Fig. 24, clockwise until the spring (B) begins to compress.

2.Turn the tension knob (A) Fig. 24 an additional 2-1/2 turns for 1/8" wide blades; 3 turns for 1/4" wide blades; and 4 turns for 3/8" wide blades. Tighten the screw (E) Fig. 25.

3.A chart (C) Fig. 24 is located at the rear of the band saw. This chart shows blade size, and the minimum radius that can be cut with each size blade.

TRACKING THE BLADE

DISCONNECT MACHINE FROM POWER SOURCE.

1.Before tracking the blade, make sure that the blade guides and blade support bearings are clear of the blade so as not to interfere with the tracking adjustment. Also make sure that the blade is tensioned properly. (Refer to section “ADJUSTING BLADE TENSION”).

2.Open the hinged door (C) Fig. 25.

3.Rotate upper wheel (A) Fig. 25, clockwise by hand and check to see if the blade (B) rides true on the approximate center of the two wheels.

4.If an adjustment is necessary, turn the blade tracking knob (D) Fig. 24 and/or Fig. 26, clockwise to move the blade to the rear, and counterclockwise to move the blade to the front. NOTE: Turn the blade tracking knob (D) in small intervals to adjust the blade tracking.

ADJUSTING UPPER BLADE GUIDE ASSEMBLY

The upper blade guide assembly (A) Fig. 26 should always be no more than 1/8" above or as close as possible to the top surface of the workpiece being cut. Loosen knob (B), rotate knob (C) and position the guide assembly (A) to the desired position. Then tighten the knob (B).

A

B

C

D

Fig. 24

E

C

B

A

Fig. 25

D

C

B

A

Fig. 26

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Band Saw General Safety Rules Safety Guidelines DefinitionsImportant Safety Instructions Stay ALERT, Watch What YOU are DOING, Failure to Follow These Rules MAY Result in Serious InjuryPower Connections Additional Safety Rules for Band SawsMotor Specifications Extension Cords Grounding InstructionsCarton Contents Unpacking and CleaningFunctional Description Band SAW Assembly Parts Stand Assembly AssemblyBand SAW to Stand Assembly Assembling Table to Machine Page Stops Attaching Lamp to MachineLocking Switch in the OFF Position Operating Controls and AdjustmentsNever Open the Door When the Machine is Running Starting and Stopping SAWAdjusting Upper Blade Guide Assembly Adjusting Blade TensionDisconnect Machine from Power Source Tracking the BladeAdjusting Upper Blade Guides and Blade Support Bearing Tilting the Table Adjusting Lower Blade Guides and Blade Support BearingAdjusting the Table Positive Stops Dust Port Changing BladesCarefully Turn the Blade Inside OUT Cutting Curves Using the Band SAWPage Probable Cause Remedy Troubleshooting GuideTrouble Blade will not Track Band SAW Blades Page Accessories MaintenanceCanadian PORTER-CABLE Delta Service Centers

BS150LS specifications

The Delta BS150LS is a highly regarded bandsaw that is designed to meet the demands of both professional woodworkers and hobbyists alike. Known for its robust construction and precision, this machine stands out in the market for its blend of power and versatility.

One of the main features of the Delta BS150LS is its powerful motor, which delivers ample cutting strength to handle a variety of materials, including hardwoods, softwoods, and even some non-ferrous metals. The motor has a horsepower rating that allows for smooth operation and ease of cutting without the need for excessive strain. This reliability in its operation makes it suitable for both intricate and heavy-duty cutting tasks.

Another notable characteristic of the BS150LS is its adequately sized cutting capacity. With a spacious table and substantial throat depth, users can tackle large workpieces with ease. The table itself can be adjusted to different angles, allowing for bevel cuts and providing enhanced flexibility for complex projects.

In terms of safety and convenience, the Delta BS150LS is equipped with features such as a blade guard and a quick-release tension lever. This enhances user safety while ensuring minimal downtime when changing blades. The machine is also designed with an integrated dust collection port, which helps maintain a cleaner workspace by minimizing sawdust accumulation.

The BS150LS incorporates advanced technology, including a precision ground cast iron table that provides a stable surface for accurate cutting. This is complemented by a robust frame that reduces vibration, thus enhancing the quality of the cuts and making the user experience smoother. Additionally, the bandsaw utilizes a well-engineered tracking system that ensures the blade remains aligned during operation, resulting in cleaner and more precise cuts.

Overall, the Delta BS150LS represents a perfect combination of power, precision, and safety features. It's ideal for users looking to elevate their woodworking capabilities, whether in a professional workshop or a home garage. With its reliable performance and versatile features, the BS150LS is a valuable addition to any woodworker’s toolkit.
Top Page Image Contents