DeWalt DW723 Definitions Safety Guidelines, Miter Saw Stand with Folding Legs Tools Required

Page 3

Definitions: Safety Guidelines

The definitions below describe the level of severity for each signal word. Please read the manual and pay attention to these symbols.

DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.

CAUTION: Used without the safety alert symbol indicates a potentially hazardous situation which, if not avoided, may result in property damage.

IFYOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY DEWALT TOOL, CALL US TOLL FREE AT: 1-800-4-DEWALT

(1-800-433-9258)

Miter Saw Stand with Folding Legs

Tools Required

1.Socket or wrench set

2.Drill with 3/8" (9.5 mm) drill bit (Not required for DEWALT Miter Saws)

3.Phillips #2 screwdriver

General Safety Instructions for Miter Saw Accessories

WARNING: To reduce the risk of personal injury:

ALWAYS use eye protection. All users and bystanders must wear eye protection that conforms to ANSI Z87.1.

DO NOT exceed the weight this stand can hold. The main center beam of the miter saw stand is designed to support 500 lbs. (227 kg.) safely in a work environment. It is unsafe to climb, sit or stand on the stand.

Follow the mounting instructions carefully. Fasten the tool to the saw mounting brackets securely as instructed.

DO NOT modify or use stand for operations for which it is unintended.

DO NOT use the stand on uneven surfaces. The stand is designed to be used on a flat, stable surface.

English

DW723

This stand is designed for use with most miter saws. If you have any problem with alignment or mounting, call 1-800-4-DEWALT (1-800-433-9258).

WARNING: For your own safety, read the miter saw instruction manual before using any accessory. Failure to heed these warnings may result in personal injury and serious damage to the miter saw and the accessory. When

servicing this tool, use only identical replacement parts.

PREPARATION

Lay the miter saw stand on the floor with the folded legs on top. Push the locking pin and pull each leg up until the locking pin (A) clicks into its detent. Lift the stand by the center beam and place it in an upright position. The stand should be stable and should not rock. Check the legs to be sure that the locking pins have engaged and the legs are firmly held in place.

A

1

Image 3
Contents DW723 Miter Saw Stand English DW723 Definitions Safety GuidelinesGeneral Safety Instructions for Miter Saw Accessories Miter Saw Stand with Folding Legs Tools RequiredAdjustable Length Extension Arm Work Stop/SupportMiter Saw Mounting Left Side Right Side DW723 Mounting Procedure ChartMinimum Removing the Saw Accessories RepairsThree Year Limited Warranty Locking Locator ClipDAY Money Back Guarantee Support de scie à onglets avec pattes pliantes DW723 Définitions lignes directrices En matière de sécuritéOutils nécessaires Ensemble butée/support de la piècePréparation Installation de la scie à onglet Tableau DE Procédure Dinstallation DW723Bras extensible réglable ’enclencherdansl’agrafedepositionnement Doit Être Poignée de transport AccessoiresAgrafe de fixation du positionneur Dégagement de la scieGarantie DE Remboursement DE 90 Jours Base para ingleteadora DW723 Definiciones Normas de seguridadHerramientas requeridas Tope/soporte para piezasPreparación Brazo de extensión de longitud ajustable Instalación de la ingleteadoraDW723 Tabla DEL Procedimiento DE Montaje = Tornillo largo, cabeza hacia arriba Pinza de seguridad del localizador Reparaciones Para quitar la sierraAsa para transporte AccesoriosServicio Gratuito DE 1 AÑO Póliza de GarantíaGarantía limitada de tres años ExcepcionesReemplazogratuitodelasetiquetasdeadvertencia