Barco 26-0503000-00 manual TçêâáåÖ=ïáíÜ=dêçìéë

Page 51

4. Operation

MatrixPRO Operating Procedures

tçêâáåÖ=ïáíÜ=dêçìéë

The MatrixPRO 8x8 DVI Router enables you to set up groups of input and output channels, in order to prevent certain inputs from being switched to selected outputs. Once established, routes can only be performed within the group.

The following rules apply:

•A minimum of two inputs and two outputs are required to form a group, but up to 8 can be included in a group.

•

•

•

•

Multiple groups can be configured on the panel (e.g., 2 groups of 4 outputs each). Inputs and outputs can only be in one group at a time.

When an output within a group is selected, you can only route the inputs currently assigned to that group. Inputs “outside” the group cannot be selected.

To check the “members” of a group, press and hold a button in the Output Selection Section. All assigned group input and output buttons will light. If no buttons light, that output is not included in a group.

Note

Grouping inputs and outputs does not establish a route. The input source for a particular output still must be established using the standard “take” procedure.

„Use the following steps to create an input/output group:

1.In the Output Selection Section, press and hold the first output that you want to be in the group.

2.While holding the output, press the buttons for the other inputs and outputs that you wish to be in the group. Each button remains lit after it is pressed.

3.Release the output button (that you pressed in step 1). The group is now configured, and routes can now only be performed within the group.

4.Repeat from step 1 to configure additional groups. Note that pressing and holding any output button within the group lights all group member buttons.

„Use the following steps to add an input or output to an existing group:

1.In the Output Selection Section, press and hold any output within the selected group. All group member buttons light.

2.While holding the output, press the buttons for the other (unlit) inputs and outputs that you wish to add to the group. Each button remains lit after it is pressed.

3.Release the output button (that you pressed in step 1). The group is now re- configured.

4.Repeat from step 1 to add additional members to the group.

„Use the following steps to remove an input or output from an existing group:

1.In the Output Selection Section, press and hold any output within the selected group. All group member buttons light.

2.While holding the output, press the buttons for the (lit) inputs and outputs that you wish to remove from the group. Each button turns off after it is pressed.

3.Release the output button (that you pressed in step 1). The group is now re- configured.

4.Repeat from step 1 to remove additional members from the group.

MatrixPRO • 8x8 DVI Router • User’s Guide

 

51

 

Page 50 Page 52
Image 51
Page 50 Page 52
Contents RëÉêÛë=dìáÇÉ UñU=asf=oçìíÉêMatrixPRO 8x8 DVI Router User’s Guide UñU=asf=oçìíÉê=√=rëÉêÛë=dìáÇÉ`çãé~åó=ÇÇêÉëë Barco Media and EntertainmentBarco N.V Aç=kçí=oÉãçîÉ=`çîÉêë=çê=m~åÉäë LéÉê~íçêë=p~ÑÉíó=pìãã~êóTokfkd QÉêãë=få=qÜáë=j~åì~ä=~åÇ=bèìáéãÉåí=j~êâáåÖ=`Ü~åÖÉ=eáëíçêó `Ü~éíÉê=N ~ÄäÉ=çÑ=`çåíÉåíë`Ü~éíÉê=R Table of Contents Help ? Få=qÜáë=`Ü~éíÉê NK==fåíêçÇìÅíáçå`Ü~éíÉê=píêìÅíìêÉ ~ÄäÉ=çÑ=`çåíÉåíë=~åÇ=fåÇÉñ Eçï=íç=rëÉ=qÜáë=dìáÇÉ`çåîÉåíáçåë= ~îáÖ~íáåÖCÉ~íìêÉë Äçìí=íÜÉ=j~íêáñmol=UñU=asf=oçìíÉêÉéäáÅ~íáçå=nìÉëíáçåë `çååÉÅíáîáíó=aá~Öê~ãNK==fåíêçÇìÅíáçå OK==e~êÇï~êÉ=lêáÉåí~íáçå Output Selection Section ~íêáñmol=UñU=asf=oçìíÉê=cêçåí=m~åÉäDisplay Section Input Selection SectionTake Button RGB Mute ButtonSetup System Factory Reset Tech SupportAáëéä~ó=pÉÅíáçå Serial Port DVI Input ConnectorsDVI Output Connectors ~íêáñmol=UñU=asf=oçìíÉê=oÉ~ê=m~åÉäAC Connector PK==fåëí~ää~íáçå ~ÑÉíó=mêÉÅ~ìíáçåë= Råé~ÅâáåÖ=~åÇ=fåëéÉÅíáçå=PáíÉ=mêÉé~ê~íáçå= ~ÅâJjçìåí=fåëí~ää~íáçå MçïÉê=`çêÇLiáåÉ=sçäí~ÖÉ=pÉäÉÅíáçå MçïÉê=fåëí~ää~íáçåPáÖå~ä=fåëí~ää~íáçå Installation QK==léÉê~íáçå MçïÉêJré=fåáíá~äáò~íáçå `çåíêçä=lîÉêîáÉïMain Menu JÉåì=qêÉÉJÉåì=póëíÉã=lîÉêîáÉï Test Pattern1400x1050 @59.94 Output All Type Ramp Operation Dhcp NìáÅâ=cìåÅíáçå=oÉÑÉêÉåÅÉFigure below illustrates the Main Menu RëáåÖ=íÜÉ=j~áå=jÉåìDhcp OFF VFD Brightness RS-232 SettingsPÉíìé=jÉåì SystemIP Address RS-232 SettingsOn the RS-232 Settings Menu, press SEL Baud Rate115200 ParametersN81255.255.255.000 SubnetTech Support Factory ResetFrom the Setup Menu, select Factory Reset SEL = Yes ESC = NoInput Status Output Status Pí~íìë=jÉåìEdid Resolution InputAll 1400x1050 @59.94 ResetBafa=oÉëçäìíáçå=jÉåì Input All Set to Default Set to Maximum Set to Minimum `~ÄäÉ=bèì~äáò~íáçå=jÉåìCable Equalization 14.MatrixPRO Test Pattern Menu sample QÉëí=m~ííÉêå=jÉåìPress Test PAT RëáåÖ=íÜÉ=qÉëí=m~ííÉêåVertical Switching FunctionEnabled SourceChSÉêíáÅ~ä=pïáíÅÜáåÖ=jÉåì Save Configuration ~îÉ=`çåÑáÖìê~íáçå=jÉåìFile OÉÅ~ää=`çåÑáÖìê~íáçå=jÉåì Recall ConfigurationMÉêÑçêãáåÖ=~=q~âÉ======= ~íêáñmol léÉê~íáåÖ=mêçÅÉÇìêÉëMÉêÑçêãáåÖ=~=jìäíáJq~âÉ `äÉ~êáåÖ=~=oçìíÉ`ÜÉÅâáåÖ=oçìíÉê=pí~íìë RëáåÖ=od=jìíÉ OçìíáåÖ=~=qÉëí=m~ííÉêåTçêâáåÖ=ïáíÜ=dêçìéë Front Panel Lockout RåäçÅâáåÖ=íÜÉ=`çåíêçä=m~åÉäRK==drf=fåëí~ää~íáçå=~åÇ=léÉê~íáçå `çåíêçä=drf=fåëí~ää~íáçå Welcome Dialog Click Next to display the Choose Destination DialogStart Installation Dialog MP Control Dialog appears OìååáåÖ=íÜÉ=drfFor Serial Connection For Ethernet ConnectionClick the Change IP Address button `çååÉÅíáçå=qêçìÄäÉëÜççíáåÖ=Active and Inactive Controls Drf=lîÉêîáÉïCáäÉ=jÉåì RëáåÖ=íÜÉ=jÉåì=~êClick Serial Port Open COM to display the COM Port Sub-menu PÉêá~ä=mçêí=jÉåì11. About Dialog Äçìí=jÉåìInputs Section RëáåÖ=íÜÉ=sáÇÉç=pïáíÅÜáåÖ=q~ÄOutputs Section Presets SectionDrf=pïáíÅÜáåÖ=léÉê~íáçåë MÉêÑçêãáåÖ=~=q~âÉ `äÉ~êáåÖ=~=oçìíÉ ~îáåÖ=mêÉëÉíë 13.Presets Section Save pendingOÉÅ~ääáåÖ=mêÉëÉíë 14.Presets Section Save pending15.Labeling Tab sample RëáåÖ=íÜÉ=i~ÄÉäáåÖ=q~Ä16.Grouping Tab sample RëáåÖ=íÜÉ=dêçìéáåÖ=q~ÄClick Remove All Group MatrixPRO 8x8 DVI Router User’s Guide Click Remove Group17.Sequencing Tab sample RëáåÖ=íÜÉ=pÉèìÉåÅáåÖ=q~ÄGUI Installation and Operation RëáåÖ=íÜÉ=pÉíìé=q~Ä 18.Setup Tab sampleRëáåÖ=íÜÉ=?Äçìí?=q~Ä SK==réÖê~ÇáåÖ=pçÑíï~êÉ PçÑíï~êÉ=réÖê~ÇÉ=lîÉêîáÉï ~êÇï~êÉ=oÉèìáêÉãÉåíëPçÑíï~êÉ=oÉèìáêÉãÉåíë Ftp//ftp.folsom.com Açïåäç~ÇáåÖ=pçÑíï~êÉSá~=cqm=páíÉ Sá~=tÉÄ=páíÉPÉêá~ä=réÖê~ÇÉ=jÉíÜçÇ RS-232 Settings None MatrixPRO 8x8 DVI Router User’s Guide BíÜÉêåÉí=réÖê~ÇÉ=jÉíÜçÇQêçìÄäÉëÜççíáåÖ=bíÜÉêåÉí=`çããìåáÅ~íáçå Upgrading Software Få=qÜáë=ééÉåÇáñ ==péÉÅáÑáÅ~íáçåëLìíéìí=péÉÅáÑáÅ~íáçåë Fåéìí=péÉÅáÑáÅ~íáçåë=MÜóëáÅ~ä=~åÇ=bäÉÅíêáÅ~ä=péÉÅáÑáÅ~íáçåë= `çããìåáÅ~íáçåë=péÉÅáÑáÅ~íáçåë=ÖÉåÅó=péÉÅáÑáÅ~íáçåë= Asf=`çååÉÅíçê Máåçìíë=BíÜÉêåÉí=`çååÉÅíçê Table below lists Ethernet connector pinoutsPÉêá~ä=`çååÉÅíçê Table below lists Serial connector pinouts==oÉãçíÉ=`çåíêçä=mêçíçÅçä AÉÑ~ìäí=fm=ÇÇêÉëë AÉÑ~ìäí=pÉêá~ä=m~ê~ãÉíÉêëCmd arg1 arg2 … argnCR OpJOPO=jçÇÉ~íêáñmol=oÉãçíÉ=`çãã~åÇë Table below lists MatrixPRO 8x8 DVI Router remote commandsExamples ~íêáñmol UñU=asf=oçìíÉê=pÉêá~ä=`çãã~åÇ=iáëíParameters None Parameters~ Listen Port Dabi=Öêé=çìí=áåParameters Out Examples Mopq=åìãOdjrqb== Qmq== 100 MatrixPRO 8x8 DVI Router User’s Guide 101 `K==`çåí~Åí=fåÑçêã~íáçå~êê~åíó OÉíìêå=j~íÉêá~ä=ìíÜçêáò~íáçå=EojF`çåí~Åí=fåÑçêã~íáçå Sales Contact InformationTechnical Support Information MatrixPRO 8x8 DVI Router User’s Guide 103 FåÇÉñIndex 105 HelpOstat 106MatrixPRO 8x8 DVI Router User’s Guide 107 SELTest PAT

26-0503000-00 specifications

The Barco 26-0503000-00 is a high-performance imaging solution designed primarily for medical applications, such as surgical theaters and diagnostic imaging. Known for its advanced technology, this display system enhances visualization and contributes significantly to the efficiency and effectiveness of medical professionals in various settings.

One of the standout features of the Barco 26-0503000-00 is its superior image quality. With a resolution of 2560 x 1600 pixels, the display provides exceptional clarity and detail, making it easier for surgeons and clinicians to analyze intricate anatomical structures. The display’s high pixel density ensures that images maintain their fidelity even when zoomed in, which is crucial during surgical interventions and diagnostic evaluations.

Equipped with advanced LED technology, the Barco display offers superior brightness and contrast ratios, resulting in vivid and realistic color reproduction. This capability is particularly important in medical imaging, where accurate color representation can be vital for diagnosis and treatment planning. The monitor also features a wide color gamut, enabling it to reproduce a diverse range of colors, ensuring all details are visible without distortion.

Another key characteristic of the Barco 26-0503000-00 is its ergonomic design. The display is often designed to reduce eye strain and enhance comfort during prolonged use. With adjustable height, tilt, and rotation, healthcare professionals can position the monitor to suit their workflow, thereby improving productivity and minimizing potential physical discomfort.

In terms of connectivity, this model supports various interfaces, including DisplayPort and HDMI, ensuring compatibility with a wide range of imaging devices. This flexibility allows for seamless integration into existing medical systems, making it an efficient choice for healthcare facilities looking to upgrade their imaging technology without significant disruptions.

Furthermore, the Barco 26-0503000-00 is built with durability in mind, featuring a robust design that can withstand the demanding environments often found in hospitals and surgical centers. The monitor is also compliant with relevant medical standards, ensuring that it meets the rigorous requirements needed for medical applications.

In summary, the Barco 26-0503000-00 is an exceptional imaging display that combines high resolution, advanced LED technology, ergonomic features, and robust connectivity options. It serves as a critical asset in medical environments, enhancing the quality of care through improved image clarity and usability for healthcare professionals.
Top Page Image Contents