Black & Decker JS630GB, JS615B instruction manual Operation

Page 8

90520768 01 js615b 7/20/07 10:22 AM Page 8

SAVE THESE INSTRUCTIONS

OPERATION

WARNING: Before attempting any of the following operations, make sure that the tool is switched off and unplugged and that the saw blade has stopped. Used saw blades can be hot.

Blade Installation (fig. A)

-Hold the saw blade (4) as shown, with teeth facing forward.

-Push the saw blade locking lever (3) downward.

-Insert the shank of the saw blade into the blade holder as far as it will go.

-Release the lever.

-Check to ensure blade is secure before cutting.

Adjusting the shoe plate for bevel cuts (fig. B)

WARNING: Never use the tool when the saw shoe is loose or removed. The shoe plate can be set to a left or right bevel angle of up to 45°.

To set the bevel angle:

-Pull the shoe plate beveling lever (9) out away from the saw to unlock the shoe plate (7) as shown in figure B.

-Slide the shoe plate (7) forward to release it from the 0° positive stop position.

-The shoe can be beveled to the left or to the right and has detents at 15°, 30° and 45°.

-Set the plate to the desired bevel angle. As you set the shoe angle the amount of degrees can be read through the bevel angle window (8). Use a protractor to verify angle accuracy.

-Push the shoe plate beveling lever (9) back towards the saw to lock the shoe plate (7).

To reset the shoe plate for straight cuts:

-Pull the shoe plate beveling lever (9) out away from the saw to unlock the shoe plate (7) as shown in figure B.

-Rotate shoe plate to an angle of approximately 0° and then pull shoe plate backwards to engage the 0° positive stop.

-Push the shoe plate beveling lever (9) back towards the saw to lock the shoe plate (7).

How to use the Sightline® feature (fig. C)

-Use a pencil to mark the cutting line.

-Position the jigsaw over the line (14).

Viewing from directly above the jigsaw the line of cut can be easily followed. Should this view be restricted for any reason, the indent (15) can be used as an alternate cutting guide.

Switching on and off

-To switch the tool on, press the on/off switch (1).

-For continuous operation, press the on/off switch (1), press the lock-on button (2) and release the on/off switch.

-To switch the tool off, release the on/off switch. To switch the tool off, when in continuous operation, press the on/off switch once more and release it.

Variable Speed Control

A speed wheel is located on the top of the saw. The speed increases as the wheel is turned from a low speed setting of 1 to a high speed setting of 7.

Setting the desired cutting mode (Choice Cut )(fig. D)

To select the proper speed and orbital action for the type of material that you are cutting, follow the steps below:

Step 1 - Turn the dial (10) as shown in figure D to the appropriate icon. Refer to the chart on page 7 for descriptions of the 7 different positions.

Step 2 - Turn the speed wheel to the recommended setting located on the icon. Step 3 - Insert the proper blade based on the chart mentioned above.

Step 4 - Perform the cut.

NOTE: These settings are initial recommendations. Your application may work best with different settings. Test these positions on similar material prior to making finished cut and adjust selections for desired results.

Connecting a vacuum cleaner to the tool

A hose adaptor (not supplied) is available at extra cost through your nearest Black & Decker service center. Insert the hose adaptor into the opening at the back of the saw. Connect a vacuum cleaner hose (not supplied) to the hose adapter.

8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Variable Speed Orbital Jigsaw VEA EL Español EN LA ContraportadaGeneral Safety Rules Work area safetySpecific Safety Rules Safety Guidelines Definitions First aid measures for gel components JS630GB onlyFunctional Description JS615B, JS630GB USE of Extension Cords Volts Total Length of Cord in FeetCounter Tops Laminate Board No orbitOperation RIP & Circle Cutting TroubleshootingHints for optimum use Troubleshooting CONT’D MaintenanceAccessories Service InformationMode D’EMPLOI Règles de sécurité générales Consignes de sécurité particulières Lignes Directrices EN Matière DE Sécurité Définitions Description fonctionnelle JS615B, JS630GB RallongesTableau de coupe « Choice Cut » Conserver CES Directives Fonctionnement MoteurInsertion de la lame fig. a Fonctionnement de la caractéristique Sightline fig. CConseils Pratiques Pour UN Usage Optimal Sciage EN Long ET Coupe CirculaireProblème Cause possible Solution possible DépannageAccessoires Information SUR LES ServicesEntretien Garantie Complète DE Deux ANS Pour Usage Résidentiel555326-7100 Normas generales de seguridad Normas de seguridad específicas Pautas DE SEGURIDAD/DEFINICIONES Descripción de las funciones JS615B, JS630GB USO DE Cables DE ExtensiónCuadro de cortes a elección Guarde Estas Instrucciones Funcionamiento MotorSugerencia Para UN USO Óptimo Almacenamiento de la hoja fig. EPara aserrar laminados Aserrado en metalProblema Causa posible Solución posible MantenimientoAccesorios Especificaciones 90520768 01 js615b 7/20/07 1022 AM

JS615B, JS630GB specifications

Black & Decker has long been synonymous with durable and efficient power tools, and the JS630GB and JS615B jigsaws are no exception. Both models are designed to cater to the needs of DIY enthusiasts and professionals alike, offering precision and versatility in woodworking tasks.

The Black & Decker JS630GB is a powerful jigsaw equipped with a 600-watt motor, which ensures that it can handle a variety of materials, including wood, metal, and plastic. This model boasts a variable speed control feature, allowing users to adjust the speed between 0 to 3,000 strokes per minute for ultimate versatility. The functionality is further enhanced by a lock-on button that allows extended operation without the need for constant pressure on the trigger, reducing fatigue during prolonged use.

Another notable feature of the JS630GB is its pendulum action control, which enables users to make aggressive cuts while maintaining accuracy. With a four-position pendulum setting, users can switch between different cutting modes based on the material being used. Additionally, the model is equipped with a tool-free blade change system, ensuring quick and easy blade swaps for seamless transitions between projects.

On the other hand, the Black & Decker JS615B offers a slightly different experience with its 500-watt motor. While it has a lower power rating, it still provides ample performance for light to medium-duty tasks. This model also features a variable speed control mechanism, allowing users to tailor the cutting speed to their specific needs. The JS615B is lightweight and designed with an ergonomic grip, which enhances comfort during use, making it ideal for intricate cuts or prolonged projects.

Both models are equipped with a built-in dust blower that keeps the cutting line clear for improved visibility, thereby enhancing precision. In terms of design, both jigsaws feature a sleek, modern aesthetic that reflects Black & Decker's commitment to quality and usability.

In summary, the Black & Decker JS630GB and JS615B jigsaws are versatile power tools that meet a range of woodworking demands. With powerful motors, variable speed controls, and user-friendly features like tool-free blade changes and ergonomic designs, they are essential additions to any workshop, whether for professional or personal use. Whether tackling larger projects or handling smaller, intricate jobs, these jigsaws deliver reliable performance and precision.
Top Page Image Contents