Hints for optimum use, RIP & Circle Cutting

90520768 01 js615b 7/20/07 10:22 AM Page 9

Blade storage (fig.E)

A blade storage compartment (11) is built-in to the side of the saw.

To open the storage door:

-Grasp the tab at the top of the door and pull outward.

The blades are held in place by a magnet.

-To release a blade, press down on one end to raise the other for access. CAUTION: Close door securely before operating saw.

Hints for optimum use

Sawing laminates

As the saw blade cuts on the upward stroke, splintering may occur on the surface closest to the shoe plate.

-Use a fine-tooth saw blade.

-Saw from the back surface of the workpiece.

-To minimize splintering, clamp a piece of scrap wood or hardboard to both sides of the workpiece and saw through this sandwich.

Sawing metal

-Be aware that sawing metal takes much more time than sawing wood.

-Use a saw blade suitable for sawing metal.

-When cutting thin metal, clamp a piece of scrap wood to the back surface of the workpiece and cut through this sandwich.

-Spread a film of oil along the intended line of cut for easier operation and longer blade life. For cutting aluminum, kerosene is preferred.

WARNING: Fire Hazard. Do not use vacuum adapter when cutting metal. Metal filings will be hot and may cause a fire.

RIP & CIRCLE CUTTING

Ripping and circle cutting without a pencil line are easily done with the rip fence and circle guide (available at extra cost).

Using the screw supplied with the accessory guide, position as shown in figure F and thread the screw into the shoe to clamp the fence securely.

When circle cutting, adjust rip fence so that distance from blade to hole in cross bar is at the desired radius and tighten screw. Place saw so that hole in cross bar is over center of circle to be cut (drill hole for blade or cut inward from edge of material to get blade into position).

When saw is properly positioned, drive a small nail through hole in cross bar. Using rip fence as a pivot arm, begin cutting circle. For circle cutting, the cross bar should be up, as shown in Figure F.

When ripping, slide the rip fence under the screw from either side of the saw. Set the cross bar at desired distance from blade and tighten screw. For ripping, the cross bar should be down and against the straight edge of the workpiece as shown in Figure G.

Problem	TROUBLESHOOTING	Possible Solution
	Possible Cause

• Unit will not start.

•Cord not plugged in.

•Circuit fuse is blown.

•Plug tool into a working outlet.

•Replace circuit fuse.

(If the product repeatedly causes the circuit fuse to blow, discontinue use immediately and have it serviced at a Black & Decker service center or authorized servicer.)

•Circuit breaker is tripped.

•Cord or switch is damaged.

•Reset circuit breaker.

(If the product repeatedly causes the circuit breaker to trip, discontinue use

immediately and have it serviced at a Black & Decker service center or authorized servicer.)

•Have cord or switch replaced at Black & Decker Service Center or Authorized Servicer.

JS615B, JS630GB specifications

Black & Decker has long been synonymous with durable and efficient power tools, and the JS630GB and JS615B jigsaws are no exception. Both models are designed to cater to the needs of DIY enthusiasts and professionals alike, offering precision and versatility in woodworking tasks.

The Black & Decker JS630GB is a powerful jigsaw equipped with a 600-watt motor, which ensures that it can handle a variety of materials, including wood, metal, and plastic. This model boasts a variable speed control feature, allowing users to adjust the speed between 0 to 3,000 strokes per minute for ultimate versatility. The functionality is further enhanced by a lock-on button that allows extended operation without the need for constant pressure on the trigger, reducing fatigue during prolonged use.

Another notable feature of the JS630GB is its pendulum action control, which enables users to make aggressive cuts while maintaining accuracy. With a four-position pendulum setting, users can switch between different cutting modes based on the material being used. Additionally, the model is equipped with a tool-free blade change system, ensuring quick and easy blade swaps for seamless transitions between projects.

On the other hand, the Black & Decker JS615B offers a slightly different experience with its 500-watt motor. While it has a lower power rating, it still provides ample performance for light to medium-duty tasks. This model also features a variable speed control mechanism, allowing users to tailor the cutting speed to their specific needs. The JS615B is lightweight and designed with an ergonomic grip, which enhances comfort during use, making it ideal for intricate cuts or prolonged projects.

Both models are equipped with a built-in dust blower that keeps the cutting line clear for improved visibility, thereby enhancing precision. In terms of design, both jigsaws feature a sleek, modern aesthetic that reflects Black & Decker's commitment to quality and usability.

In summary, the Black & Decker JS630GB and JS615B jigsaws are versatile power tools that meet a range of woodworking demands. With powerful motors, variable speed controls, and user-friendly features like tool-free blade changes and ergonomic designs, they are essential additions to any workshop, whether for professional or personal use. Whether tackling larger projects or handling smaller, intricate jobs, these jigsaws deliver reliable performance and precision.