BM 1619X00905 3-05 3/24/05 11:00 PM Page 9
Operating Instructions
DEPTH ADJUSTMENT
Disconnect plug from power source. Loosen the depth adjustment lever located between the guard and handle of saw. Hold the foot down with one hand and raise or lower saw by the
handle. Tighten lever at the depth setting desired. Check desired depth (Fig. 3).
Not more than one tooth length of the blade should extend below the material to be cut, for minimum splintering (Fig. 4).
| FIG. 3 |
|
| DEPTH |
|
|
|
|
| FIG. 4 | |||||
|
|
|
| ADJUSTMENT LEVER |
|
| |
|
|
|
| CALIBRATED |
|
|
|
|
|
|
| DEPTH BRACKET |
|
|
|
|
|
|
| Outer Scale Calibrated |
|
|
|
|
|
|
| For Standard |
|
|
|
|
|
|
|
|
| ||
|
|
|
| Lumber Sizes |
|
|
|
|
|
|
| 60° MARK TO BE | ONE TOOTH LENGTH SHOULD | ||
|
|
|
| ADJUSTED PRIOR TO | |||
|
|
|
| ||||
| Inner Scale |
| BEVEL ADJUSTMENT |
| PENETRATE WOOD FOR | ||
|
| ||||||
Calibrated In Inches |
| (60° ONLY) |
| MINIMUM SPLINTERING | |||
|
|
|
|
|
|
|
|
90° CUTTING ANGLE CHECK
Disconnect plug from power source. Set foot to maximum depth of cut setting. Loosen bevel adjustment lever, set to 0° on quadrant, retighten lever and check for 90° angle between the blade and bottom plane of foot with a square (Fig. 5). Make adjustments by turning the small alignment screw, if necessary (Fig. 6).
| FIG. 5 |
| BEVEL |
| FIG. 6 |
|
|
| ADJUSTMENT |
|
|
|
|
|
|
| |
|
|
| LEVER |
|
|
90° | FOOT | ALIGNMENT | |||
BLADE |
| ||||
| SCREW | ||||
BEVEL ADJUSTMENT
Disconnect plug from power source. The foot can be adjusted up to 45° by loosening the bevel adjustment lever at the front of the saw. Align to desired angle on calibrated quadrant. Then tighten bevel adjustment lever (Fig. 7). For 60° loosen depth adjustment lever, lower foot to 60° mark on depth bracket (Fig. 3), and tighten lever. Loosen bevel adjustment lever, depress 45° stop spring (Fig. 8), align foot to 60 mark on quadrant and tighten lever. Because of the increased amount of blade engagement in the work and decreased stability of the foot,
blade binding may occur. Keep the saw steady and the foot firmly on the workpiece.
| QUADRANT | |
| BEVEL | |
| ADJUSTMENT | |
FIG. 7 | ||
LEVER | ||
|
LINE GUIDE
For a straight 90° cut, use right side of notch in the foot. For 45° and 60° bevel cuts, use the left side (Fig. 8). The cutting guide notch will give an approximate line of cut. Make sample cuts in scrap lumber to verify actual line of cut. This will be helpful because of the number of different blade types and thicknesses available. To ensure minimum splintering on the good side of the material to be cut, face the good side down.
45° STOP |
|
| 45° BEVEL | 90° VERTICAL | |||||
|
| CUTS |
|
|
|
|
| CUTS | |
|
|
|
|
|
| ||||
SPRING |
| 60° BEVEL |
|
|
|
|
| ||
|
|
|
|
|
|
|
| ||
PUSH 45° |
| CUTS |
|
|
| ||||
STOP |
|
|
|
|
|
|
|
| |
SPRING IN |
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
| FIG. 8 | ||
DIRECTION |
|
|
|
|
|
|
| ||
OF ARROW |
|
|
|
|
|
|
|
| |
FOR 60° |
|
|
|
|
|
|
|
| |