Chicago Electric 42933 operating instructions Nameplate Extension Cord, 25’ 50’ 100’ 150’

Page 4

8.USE RIGHT TOOL. Don’t force tool or attachment to do a job for which it was not designed.

RECOMMENDED MINIMUM WIRE GAUGE FOR EXTENSION CORDS

(120 VOLT)

NAMEPLATE

EXTENSION CORD

AMPERES

 

LENGTH

 

(at full load)

25’

50’

100’

150’

0 – 6

18

16

16

14

 

 

 

 

 

6.1 – 10

18

16

14

12

 

 

 

 

 

10.1 – 12

16

16

14

12

 

 

 

 

 

12.1 – 16

14

12

Do not use.

 

 

 

 

 

TABLE A

 

 

 

 

9.USE PROPER EXTENSION CORD. Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and over- heating. Table A shows the correct size to use depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord.

10.WEAR PROPER APPAREL. Do not wear loose clothing, gloves, neck- ties, rings, bracelets, or other jewelry which may get caught in moving parts. Nonslip footwear is recom- mended. Wear protective hair cover- ing to contain long hair.

11.ALWAYS USE SAFETY GLASSES. Also use face or dust mask if cutting operation is dusty. Everyday eye- glasses only have impact resistant lenses, they are NOT safety glasses.

12.SECURE WORK. Use clamps or a vise to hold work when practical. It’s

safer than using your hand and it frees both hands to operate tool.

13.DON’T OVERREACH. Keep proper footing and balance at all times.

14.MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for best and safest performance. Follow instructions for lubricating and chang- ing accessories.

15.DISCONNECT TOOLS before ser- vicing; when changing accessories, such as blades, bits, cutters, and the like.

16.REDUCE THE RISK OF UNINTEN- TIONAL STARTING. Make sure switch is in off position before plug- ging in.

17.USE RECOMMENDED ACCESSO- RIES. Consult the owner’s manual for recommended accessories. The use of improper accessories may cause risk of injury to persons.

18.NEVER STAND ON TOOL. Serious injury could occur if the tool is tipped or if the cutting tool is unintentionally contacted.

19.CHECK DAMAGED PARTS. Before further use of the tool, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and per- form its intended function – check for alignment of moving parts, binding of moving parts, breakage of parts, mounting, and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced.

20.DIRECTION OF FEED. Feed work into a blade or cutter against the direction of rotation of the blade or cutter only.

SKU 42933

For technical questions, please call 1-800-444-3353.

Page 4

Image 4
Contents For technical questions or replacement parts, please call Distributed exclusively by Harbor Freight ToolsContents Save This Manual General Tool Safety WarningsSave all warnings and instructions for future reference Nameplate Extension Cord 25’ 50’ 100’ 150’Radial Arm Saw Safety Warnings Grounding InstructionsWith Three Prong Plugs 125 V~ 3-Prong Plug and OutletNot a safe method Essential Straight Push-stick Features Functions Diagram not to scaleHandle Notch Stick LengthFor technical questions, please call Vibration Safety Installation SpecificationsUnpacking SKU For technical questions, please call Operating Controls For technical questions, please call Adjustments Cord to the Radial Arm SawCutting Kerf Marks Cross Cutting OperationMitre Cross Cutting Bevel Cross Cutting Compound Cross CuttingOut-Rip Cutting Maintenance Troubleshooting Problem Cause SolutionParts List Part Description ’tyAssembly Diagram Record Product’s Serial Number HereAssembly Diagram Limited 90 DAY Warranty