Craftsman 137.218030, 137218030001 operating instructions Assemblestandfig.A

Page 10

ASSEMBLESTAND(FIG.A)

1.Unpackallpartsandgroupbytypeandsize(Fig.A). Referto partslistforquantities.

2.Attachonelonguppersupport(P)totopofleg(S) usingonesquareneckbolt(1)andnut(2). NOTE:

•Aligndetentsinstandlegwithsupportbracketsto ensureproperfit.

•Donottightenboltsuntilstandis properly aligned(seestep#8 beforetightening).

3.Attachotherendof longuppersupporttotopof anotherlegusingonesquareneckboltandnut.

4.Attachonelongbottomsupport(R)tocenterofeach

legusingsquareneckboltsandnuts.Thiscompletes

thefrontframesection.

5.Assemblerearframesectioninexactlythesame way.

6.Joinfrontandrearframeassembliesusingtwo shortuppersupports(O)andtwoshortbottom supports(Q),squareneckboltsandnuts.

7.Insertlargehexheadbolt(3)intorubberfoot(4)and insertintobottomof leg.Fastenwithwasher(5)and nut(6).Repeatforeachleg.

8.Attachthehook(7)totheleftofthestandwithbolt(8)

andnut(9)forthemitergaugestorageAttachthe.

hook(12)totherightofthestandwithboltandnut

fortheripfencestorage.

9.Placestandonlevelsurfaceandadjustsoalllegs arecontactingthefloorandareatsimilarangles tothefloor,anddetents(13)in standlegalignwith supportbrackets,thentightenallbolts. NOTE:Standshouldnotrockafterall boltsare tightened.

Fig, A

Q

S

ASSEMBLETABLESAWTOSTAND(FIG.A, B)

1.Placeprotectivecorrugatedcardboardoroldblanket onfloortoprotectthesawtablesurface.

2.Placethesawup-sidedownontheprotective material(Fig.B).

3.Positionthestandup-sidedownonthesawbase. NOTE:Makesurefrontofstandandfrontof saware facingthesamedirection.

4.Lineupthefourholesinsawbaseandstand.

5.Fastensawtostandusingfourbolts(10),washers

(11) andnuts(8).

NOTE:Placewasheroneach bolt before inserting into saw base and through the support. Nut must be flush against the bracket (see Fig. A).

6.Tighten all four nuts.

7.Carefully set the saw in its upright position on a clean level surface.

NOTE: DO NOT OVER TIGHTEN NUTS HOLDING SAW TO STAND. THIS MAY DAMAGE THE SAW BASE.

IA WARNING

IF THE STAND WILL NOT BE USED, DO NOT OPERATE THE TABLE SAW ON THE FLOOR. THIS IS A VERY DANGEROUS POSITION.

Fig, B

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Operators Manual 10 in. Table SAW WiTH Stand Visit our Craftsman WebsiteMotor SectionSAW Balance at all times WAn.I.GJDo not OVERREACH. Keep proper footing Check for Damaged or Loose PartsFreehand Cutting is the Major Cause Grounding iNSTRUCTiONS IA Warning Unpacking Your Table SAW ON/OFF BLADEELEVATIONHANDWHEEL- Raisesand lowerstheblade ASSEMBLESTANDFIG.A Storage FIG. B=f, FiG. B-2 Rip fence and miter gauge Installing and Changing the Blade FIG. G, H IA WarningRunning Installing the Table Extension FenceAvoid Kickbacks FIG. L Serious injuryAdjustment iNSTRUCTiONS Miter Gauge Adjustment FIG. OBlade Tilt Pointer IA wAR.I.GIBlade Parallel to the Miter Gauge Groove FIG. S, T Tools Required Additional Blade Adjustments FIG. TAdjustment Procedure FrontRaise the Blade FIG, U ON/OFF Switch FIGUsing the Table Extension Fence Overload Protection FIGTime Enough to cause a severe injury WARNI.IeIA WARNINe Kickback and serious injury to the user canIA WARNlaGI Fig,AAAwaRmnGI Dado Cuts FIG. EEBlade Raising and Tilting Mechanism General MaintenanceLubrication Not run, contact Sears Service Center at 1-800-4-MY=HOME Symptom Possible Causes Corrective ActionSears Service Center Parts List for Table SAW SchematicSchematic Parts LiST and Schematic for Motor Parts LiST and Schematic for Stand QtyCut Here To Push 1/2 Wood Push 3/4 Page Your Home

137218030001, 137.218030 specifications

The Craftsman 137.218030, also known as the 137218030001, is a standout tool in the realm of woodworking and home improvement. This model is primarily recognized for its versatility and reliability, making it a popular choice among both professionals and DIY enthusiasts. Designed with a keen focus on user-friendliness, the saw incorporates several key features and technologies that elevate its performance.

One of the most significant aspects of the Craftsman 137.218030 is its powerful motor. With an impressive horsepower rating, this tool ensures efficient cutting through various types of materials, including hardwood, softwood, and composites. The motor is also designed to minimize vibration, resulting in smoother operation which enhances accuracy and prolongs the life of the tool.

In terms of design, the Craftsman 137.218030 boasts an adjustable bevel capability, allowing users to make precise angle cuts for more complex projects. The bevel range provides flexibility for a variety of applications, enabling craftspeople to execute intricate designs and professional-quality finishes with ease. Additionally, the adjustable cutting depth feature is instrumental for users seeking different material thicknesses, enhancing the tool's adaptability and usability.

Another notable feature is the integrated safety mechanisms. The Craftsman 137.218030 comes equipped with a blade guard that helps prevent accidental contact with the cutting blade. This is crucial for promoting safer operation during use. The trigger lock feature also adds an extra layer of security, preventing unauthorized use and ensuring that the saw only activates when intended.

The versatility of the Craftsman 137.218030 is further enhanced by its compatibility with a wide range of accessories, including different blades and attachments. This flexibility enables users to switch from cutting to sanding or even polishing with relative ease, thus making it a multi-functional tool for various projects.

Moreover, the Craftsman brand is known for its commitment to quality, and this model is no exception. Built to withstand the rigors of daily use, the durability of the 137.218030 ensures that it remains a dependable addition to any workshop. Overall, the Craftsman 137.218030,137218030001 combines robust performance, advanced technology, and user-centric features, making it an excellent choice for anyone looking to elevate their crafting experience. Its blend of power, safety, and versatility truly encapsulates what modern tools strive to achieve.
Top Page Image Contents