Craftsman 137218030001 WAn.I.GJ, Do not OVERREACH. Keep proper footing, Balance at all times

Page 3

GENERAL SAFETY iNSTRUCTiONS

Read and understand all the instructions below before using the power

meant to cover every possible condition that could occur. As with any and due care must be used.

tool. These safety instructions are not power tool, common sense, vigilance

READ and become familiar with this entire Operator's Manual. LEARN the tool'sapplications, limitations and possible hazards.

2.[A wAn.I.GJ

Look for this symbol that identifies important safety precautions. It means BE ALERTt YOUR SAFETY IS iNVOLVED!

adjusting wrenches are removed from the tool before turning ON.

16.NEVER LEAVE TOOL RUNNING UNATTENDED. TURN THE POWER OFF. Do not leave the tool

before the blade comes to a complete stop.

17.NEVER STAND ON TOOL. Serious injury could occur if the tool is tipped or if the cutting tool is unintentionally contacted.

3.NEVER OPERATE THIS MACHINE WITHOUT THE

SAFETY

GUARD iN PLACE FOR ALL THROUGH=

18. DO NOT OVERREACH. Keep proper footing and

SAWING

OPERATIONS.

balance at all times.

4.DO NOT USE iN A DANGEROUS ENVIRONMENT such as damp or wet locations or in the rain. Keep work area well lighted.

5.DO NOT use power tools in the presence of flammable liquids or gases.

6.KEEP WORK AREA CLEAN. Cluttered areas and benches invite accidents.

7.KEEP CHILDREN AWAY. All visitors should be kept at a safe distance from the work area.

8.DO NOT FORCE THE TOOL. It will do the job better and safer if used at the rate for which it was

designed.

9.USE THE RIGHT TOOL. Do not force the tool or attachment to do a job for which it is not designed.

10.WEAR PROPER APPAREL. DO NOT wear loose clothing, gloves, neckties, rings, bracelets or other jewelry that may get caught in moving parts. Non- slip footwear is recommended. Wear protective hair covering to contain long hair.

11.WEAR A FACE MASK OR DUST MASK. Sawing, cutting and sanding operations produce dust.

12.DISCONNECT TOOLS before servicing and when changing accessories, such as blades, cutters, etc.

13.REDUCE THE RISK OF UNINTENTIONAL STARTING. Make sure the switch is in the OFF position before plugging tool into the power supply.

14.USE ONLY RECOMMENDED ACCESSORIES. Consult the Operator's Manual for recommended accessories. The use of improper accessories may cause injury to you or damage to the tool.

15.REMOVE ADJUSTING KEYS AND WRENCHES. Form the habit of checking to see that keys and

19.MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for most efficient and safest performance.

Follow instructions for lubricating and changing accessories.

20.CHECK FOR DAMAGED OR LOOSE PARTS.

Check for alignment of moving parts, binding of moving parts, loose mounting and any other conditions that may affect its safe operation. A guard or other part that is loose or damaged should be properly adjusted, repaired or replaced.

21.MAKE WORKSHOP CHILDPROOF with padlocks, master switches or by removing starter keys.

22.DO NOT operate the tool if you are under the influence of any drugs, alcohol or medication that could impair your ability to use the tool safely.

23.USE A DUST COLLECTION SYSTEM whenever

possible. Dust generated from certain materials can be hazardous to your health and, in some cases,

a fire hazard. Always operate the power tool in a well-ventilated area with adequate dust removal.

24.ALWAYS WEAR EYE PROTECTION. Any power tool can throw debris into your eyes that could cause permanent eye damage. ALWAYS wear safety goggles (not glasses) that comply with ANSI safety standard Z87.1. Everyday glasses have only impact resistant lenses. They ARE NOT safety glasses.

NOTE: Glasses or goggles not in compliance with ANSI Z87.1 could cause serious injury when they break.

25.DiRECTiON OF FEED. Feed work into a blade or

cutter against the direction of rotation of the blade or cutter only.

26.DO NOT loan your tool to a neighbor or friend without providing him/her with the Operator's Manual. Be sure he/she learns the tool's applications and possible hazards.

Page 2 Page 4
Image 3
Page 2 Page 4
Contents Visit our Craftsman Website Operators Manual 10 in. Table SAW WiTH StandSection MotorSAW Check for Damaged or Loose Parts WAn.I.GJDo not OVERREACH. Keep proper footing Balance at all timesFreehand Cutting is the Major Cause Grounding iNSTRUCTiONS IA Warning Unpacking Your Table SAW ON/OFF BLADEELEVATIONHANDWHEEL- Raisesand lowerstheblade ASSEMBLESTANDFIG.A Storage FIG. B=f, FiG. B-2 Rip fence and miter gauge IA Warning Installing and Changing the Blade FIG. G, HSerious injury Installing the Table Extension FenceAvoid Kickbacks FIG. L RunningMiter Gauge Adjustment FIG. O Adjustment iNSTRUCTiONSIA wAR.I.GI Blade Tilt PointerBlade Parallel to the Miter Gauge Groove FIG. S, T Front Additional Blade Adjustments FIG. TAdjustment Procedure Tools RequiredOverload Protection FIG ON/OFF Switch FIGUsing the Table Extension Fence Raise the Blade FIG, UTime Kickback and serious injury to the user can WARNI.IeIA WARNINe Enough to cause a severe injuryFig,AA IA WARNlaGIDado Cuts FIG. EE AwaRmnGIGeneral Maintenance Blade Raising and Tilting MechanismLubrication Symptom Possible Causes Corrective Action Not run, contact Sears Service Center at 1-800-4-MY=HOMEParts List for Table SAW Schematic Sears Service CenterSchematic Parts LiST and Schematic for Motor Qty Parts LiST and Schematic for StandCut Here To Push 1/2 Wood Push 3/4 Page Your Home

137218030001, 137.218030 specifications

The Craftsman 137.218030, also known as the 137218030001, is a standout tool in the realm of woodworking and home improvement. This model is primarily recognized for its versatility and reliability, making it a popular choice among both professionals and DIY enthusiasts. Designed with a keen focus on user-friendliness, the saw incorporates several key features and technologies that elevate its performance.

One of the most significant aspects of the Craftsman 137.218030 is its powerful motor. With an impressive horsepower rating, this tool ensures efficient cutting through various types of materials, including hardwood, softwood, and composites. The motor is also designed to minimize vibration, resulting in smoother operation which enhances accuracy and prolongs the life of the tool.

In terms of design, the Craftsman 137.218030 boasts an adjustable bevel capability, allowing users to make precise angle cuts for more complex projects. The bevel range provides flexibility for a variety of applications, enabling craftspeople to execute intricate designs and professional-quality finishes with ease. Additionally, the adjustable cutting depth feature is instrumental for users seeking different material thicknesses, enhancing the tool's adaptability and usability.

Another notable feature is the integrated safety mechanisms. The Craftsman 137.218030 comes equipped with a blade guard that helps prevent accidental contact with the cutting blade. This is crucial for promoting safer operation during use. The trigger lock feature also adds an extra layer of security, preventing unauthorized use and ensuring that the saw only activates when intended.

The versatility of the Craftsman 137.218030 is further enhanced by its compatibility with a wide range of accessories, including different blades and attachments. This flexibility enables users to switch from cutting to sanding or even polishing with relative ease, thus making it a multi-functional tool for various projects.

Moreover, the Craftsman brand is known for its commitment to quality, and this model is no exception. Built to withstand the rigors of daily use, the durability of the 137.218030 ensures that it remains a dependable addition to any workshop. Overall, the Craftsman 137.218030,137218030001 combines robust performance, advanced technology, and user-centric features, making it an excellent choice for anyone looking to elevate their crafting experience. Its blend of power, safety, and versatility truly encapsulates what modern tools strive to achieve.
Top Page Image Contents