Craftsman 137218030001, 137.218030 Storage FIG. B=f, FiG. B-2 Rip fence and miter gauge

Page 11

STORAGE (FIG. B=f, FiG. B-2)

Rip fence and miter gauge

1.Storage bracket for the rip fence (1) is located on the right side of the stand.

2.Storage bracket for the miter gauge (2) is located on the left side of the stand.

Fig. B-f

Fig. B-2

-2

MOUNTING SAW ONTO WORK SURFACE (FIG. C)

1.tf the leg set will not be used, the saw must be properly secured to a sturdy workbench using the four mounting holes at the base of the saw.

2.The surface of the table where the saw is to be mounted must have a hole large enough to facilitate sawdust fall-through and removal.

3.Square the saw on the mounting surface and mark the location of the four 3/8 in. mounting holes (1).

4.Drill 3/8 in. hole into the mounting surface.

5.Mark an 11 in. square (2) centered between the four mounting holes (1).

6.Cut out and remove the square.

7.This opening will allow sawdust to fall through the saw base.

8.Place the saw on the work surface and align the mounting holes of the saw with those drilled through the surface.

9.Fasten the saw to the work surface.

[A WARNING

Do not operate this machine on the floor. This is very dangerous and may cause serious injury.

Fig. C

SQUARE

CUTOUT _-- 2

1

I,AWARNING!

Failure to provide the sawdust fall=through hole for use of the saw when mounted to a work surface and

not the stand will cause sawdust to build up in the motor area, which may result in fire or cause motor damage.

KEEPING THE AREA CLEAN

1.Sawdust and wood chips that fall from under the saw will accumulate on the floor.

2.Make it a practice to pick up and discard this dust when you have completed cutting.

BLADE RAISING HANDWHEEL (FIG. D, E)

1.Attach the up-down handwheel (1) to the elevation rod (2) at the front of the saw. Make sure the slots (3) in the hub of the handwheel (1) engage with the pins (4).

2.Attach and tighten the dome nut (5 - Fig. E).

Fig. D

1

BLADE TILTING HANDWHEEL (FIG. E)

1.Attach the bevel 0° - 45° handwheel (6) to the blade tilting rod on the right side of the saw in the same manner as above.

2.Attach and tighten the handwheel dome nut (5).

Fig. E

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Visit our Craftsman Website Operators Manual 10 in. Table SAW WiTH StandSAW SectionMotor Check for Damaged or Loose Parts WAn.I.GJDo not OVERREACH. Keep proper footing Balance at all timesFreehand Cutting is the Major Cause Grounding iNSTRUCTiONS IA Warning Unpacking Your Table SAW ON/OFF BLADEELEVATIONHANDWHEEL- Raisesand lowerstheblade ASSEMBLESTANDFIG.A Storage FIG. B=f, FiG. B-2 Rip fence and miter gauge IA Warning Installing and Changing the Blade FIG. G, HSerious injury Installing the Table Extension FenceAvoid Kickbacks FIG. L RunningMiter Gauge Adjustment FIG. O Adjustment iNSTRUCTiONSBlade Parallel to the Miter Gauge Groove FIG. S, T IA wAR.I.GIBlade Tilt Pointer Front Additional Blade Adjustments FIG. TAdjustment Procedure Tools RequiredOverload Protection FIG ON/OFF Switch FIGUsing the Table Extension Fence Raise the Blade FIG, UTime Kickback and serious injury to the user can WARNI.IeIA WARNINe Enough to cause a severe injuryFig,AA IA WARNlaGIDado Cuts FIG. EE AwaRmnGILubrication General MaintenanceBlade Raising and Tilting Mechanism Symptom Possible Causes Corrective Action Not run, contact Sears Service Center at 1-800-4-MY=HOMEParts List for Table SAW Schematic Sears Service CenterSchematic Parts LiST and Schematic for Motor Qty Parts LiST and Schematic for StandCut Here To Push 1/2 Wood Push 3/4 Page Your Home

137218030001, 137.218030 specifications

The Craftsman 137.218030, also known as the 137218030001, is a standout tool in the realm of woodworking and home improvement. This model is primarily recognized for its versatility and reliability, making it a popular choice among both professionals and DIY enthusiasts. Designed with a keen focus on user-friendliness, the saw incorporates several key features and technologies that elevate its performance.

One of the most significant aspects of the Craftsman 137.218030 is its powerful motor. With an impressive horsepower rating, this tool ensures efficient cutting through various types of materials, including hardwood, softwood, and composites. The motor is also designed to minimize vibration, resulting in smoother operation which enhances accuracy and prolongs the life of the tool.

In terms of design, the Craftsman 137.218030 boasts an adjustable bevel capability, allowing users to make precise angle cuts for more complex projects. The bevel range provides flexibility for a variety of applications, enabling craftspeople to execute intricate designs and professional-quality finishes with ease. Additionally, the adjustable cutting depth feature is instrumental for users seeking different material thicknesses, enhancing the tool's adaptability and usability.

Another notable feature is the integrated safety mechanisms. The Craftsman 137.218030 comes equipped with a blade guard that helps prevent accidental contact with the cutting blade. This is crucial for promoting safer operation during use. The trigger lock feature also adds an extra layer of security, preventing unauthorized use and ensuring that the saw only activates when intended.

The versatility of the Craftsman 137.218030 is further enhanced by its compatibility with a wide range of accessories, including different blades and attachments. This flexibility enables users to switch from cutting to sanding or even polishing with relative ease, thus making it a multi-functional tool for various projects.

Moreover, the Craftsman brand is known for its commitment to quality, and this model is no exception. Built to withstand the rigors of daily use, the durability of the 137.218030 ensures that it remains a dependable addition to any workshop. Overall, the Craftsman 137.218030,137218030001 combines robust performance, advanced technology, and user-centric features, making it an excellent choice for anyone looking to elevate their crafting experience. Its blend of power, safety, and versatility truly encapsulates what modern tools strive to achieve.
Top Page Image Contents