Craftsman 137218030001, 137.218030 operating instructions Grounding iNSTRUCTiONS

Page 5

GROUNDING iNSTRUCTiONS

tN THE EVENT OF A MALFUNCTION OR BREAKDOWN, grounding provides a path of least resistance for electric currents and reduces the risk of electric shock. This tool is equipped with an electrical cord that has an equipment-grounding conductor

and a grounding plug. The plug must be plugged into a matching receptacle that is properly installed and grounded in accordance with all local codes and ordinances.

DO NOT MODIFY THE PLUG PROVIDED. If it will not fit the receptacle, have the proper receptacle installed by a qualified electrician.

IMPROPER CONNECTION of the equipment grounding conductor can result in risk of electric shock. The conductor with the green insulation (with or without yellow stripes) is the equipment grounding conductor.

tf repair or replacement of the electrical cord or plug is necessary, do not connect the equipment grounding conductor to a live terminal.

CHECK with a qualified electrician or service person if you do not completely understand the grounding instructions, or if you are not certain the tool is properly grounded.

USE only three-wire extension cords that have three- pronged grounding plugs with three-pole receptacles that accept the tool'splug. Repair or replace damaged or worn cords immediately.

GUiDELiNES FOR EXTENSION CORDS

USE THE PROPER EXTENSION CORD. Make sure your extension cord is in good condition. Use an extension cord heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power,

overheating and burning out of the motor. The table on the right shows the correct size to use depending on cord length and nameplate ampere rating, tf in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord.

Make sure your extension cord is properly wired and in good condition. Always replace a damaged extension cord or have it repaired by a qualified technician before using it. Protect your extension cords from sharp objects, excessive heat and damp or wet areas.

Use a separate electrical circuit for your tool. This circuit must not be less than #12 wire with a 20 A time-lag fuse

or a #14 wire with a 15 A time-lag fuse. NOTE: When using an extension cord on a circuit with a #14 wire, the extension cord must not exceed 25 feet in length. Before connecting the motor to the power line, make sure the switch is in the off position and the electric current is rated the same as the current stamped on the motor nameplate. Running at a lower voltage will damage the motor. This tool is intended for use on a circuit that has a receptacle like the one illustrated in Fig. 1.

Fig. 1 shows a three-pronged electrical plug and receptacle that has a grounding conductor. If a properly grounded receptacle is not available, an adapter (Fig. 2) can be used to temporarily connect this plug to a two- contact grounded receptacle. The adapter (Fig. 2) has a rigid lug extending from it that MUST be connected to a permanent earth ground, such as a properly grounded receptacle box.

CAUTION

In all cases, make certain the receptacle is properly grounded, if you are not sure, have a qualified electrician check the receptacle.

CAUTION

This tool is for indoor use only. Do not expose to rain or use in damp locations.

Fig. 1

ged Plug

g Prong

Properly Grounded

Three-Pronged Receptacle

Fig. 2

Grounding Lug

 

Make sure this is connected to a known ground.

Two-Pronged

Adapter Receptacle

CAUTION

This tool must be grounded while in use to protect the operator from electric shock.

'

O"

O'm

'

(When using 120volts only)

Ampere RatingTotal length of Cord

MoreThan NotMoreThan 25ft. 50ft. 100ft. 150ft.

0

6

8

16

16

14

6

10

8

I6

14

12

10

12

6

16

14

12

Image 5
Contents Visit our Craftsman Website Operators Manual 10 in. Table SAW WiTH StandSAW SectionMotor Do not OVERREACH. Keep proper footing WAn.I.GJBalance at all times Check for Damaged or Loose PartsFreehand Cutting is the Major Cause Grounding iNSTRUCTiONS IA Warning Unpacking Your Table SAW ON/OFF BLADEELEVATIONHANDWHEEL- Raisesand lowerstheblade ASSEMBLESTANDFIG.A Storage FIG. B=f, FiG. B-2 Rip fence and miter gauge IA Warning Installing and Changing the Blade FIG. G, HAvoid Kickbacks FIG. L Installing the Table Extension FenceRunning Serious injuryMiter Gauge Adjustment FIG. O Adjustment iNSTRUCTiONSBlade Parallel to the Miter Gauge Groove FIG. S, T IA wAR.I.GIBlade Tilt Pointer Adjustment Procedure Additional Blade Adjustments FIG. TTools Required FrontUsing the Table Extension Fence ON/OFF Switch FIGRaise the Blade FIG, U Overload Protection FIGTime IA WARNINe WARNI.IeEnough to cause a severe injury Kickback and serious injury to the user canFig,AA IA WARNlaGIDado Cuts FIG. EE AwaRmnGILubrication General MaintenanceBlade Raising and Tilting Mechanism Symptom Possible Causes Corrective Action Not run, contact Sears Service Center at 1-800-4-MY=HOMEParts List for Table SAW Schematic Sears Service CenterSchematic Parts LiST and Schematic for Motor Qty Parts LiST and Schematic for StandCut Here To Push 1/2 Wood Push 3/4 Page Your Home

137218030001, 137.218030 specifications

The Craftsman 137.218030, also known as the 137218030001, is a standout tool in the realm of woodworking and home improvement. This model is primarily recognized for its versatility and reliability, making it a popular choice among both professionals and DIY enthusiasts. Designed with a keen focus on user-friendliness, the saw incorporates several key features and technologies that elevate its performance.

One of the most significant aspects of the Craftsman 137.218030 is its powerful motor. With an impressive horsepower rating, this tool ensures efficient cutting through various types of materials, including hardwood, softwood, and composites. The motor is also designed to minimize vibration, resulting in smoother operation which enhances accuracy and prolongs the life of the tool.

In terms of design, the Craftsman 137.218030 boasts an adjustable bevel capability, allowing users to make precise angle cuts for more complex projects. The bevel range provides flexibility for a variety of applications, enabling craftspeople to execute intricate designs and professional-quality finishes with ease. Additionally, the adjustable cutting depth feature is instrumental for users seeking different material thicknesses, enhancing the tool's adaptability and usability.

Another notable feature is the integrated safety mechanisms. The Craftsman 137.218030 comes equipped with a blade guard that helps prevent accidental contact with the cutting blade. This is crucial for promoting safer operation during use. The trigger lock feature also adds an extra layer of security, preventing unauthorized use and ensuring that the saw only activates when intended.

The versatility of the Craftsman 137.218030 is further enhanced by its compatibility with a wide range of accessories, including different blades and attachments. This flexibility enables users to switch from cutting to sanding or even polishing with relative ease, thus making it a multi-functional tool for various projects.

Moreover, the Craftsman brand is known for its commitment to quality, and this model is no exception. Built to withstand the rigors of daily use, the durability of the 137.218030 ensures that it remains a dependable addition to any workshop. Overall, the Craftsman 137.218030,137218030001 combines robust performance, advanced technology, and user-centric features, making it an excellent choice for anyone looking to elevate their crafting experience. Its blend of power, safety, and versatility truly encapsulates what modern tools strive to achieve.