Craftsman 137.21229 operating instructions Mounting the Miter SAW FIG, O

Page 15

MOUNTING THE MITER SAW (FIG, O)

To avoid injury from unexpected mew movement:

,Before moving the saw, disconnect the power cord from the outlet, and !ock the cutting arm in the lower position using the stop latch.

NOTE: The stop latch is for carrying or storing the tooL It is not to be used for holding the saw while cutting. Lower blade and press in stop latch to secure saw for transport or storage.

Never carry the miter saw by the power cord or by the switch handle. Carrying the tool by the power cord could cause damage to the insulation or wire connections resulting in electric shock or fire.

To avoid injury from flying debris, do not allow visitors to stand behind the saw.

Place the saw on a firm, level work-surface where there is room for handling and properly supporting the workpiece.

Support the saw on a leve! work surface.

Bolt or clamp the saw to its support.

Place the saw in the desired location, either on a work bench or recommended leg seL The base of the saw has three mounting holes (1).

For etetionery use, fasten the saw to a workbench. For po_ebte uee, fasten the saw to a 3/4 in. piece of plywood. This mounting board can then be clamped to a secure surface.

Fig. 0

Portable Use

Hand Hold

3/4 Inch Plywood

Stationery Uee

15

Image 15
Contents Sears, Roebuck and Co., Hoffman Estates, IL 60179 USA Operators Manuam 10 in. Compound Miter SAW Modem NoMiter SAW ONE-YEAR Full Warranty on Craftsman ToolWARNmNG Motor15DISCONNECT Tools from Power Source General Safety mNSTRUCTmONS Before USmNG this Power ToolSPECiFiC Safety mNSTRUCTmONS for THiS Compound Minter SAW GUmDEUNES for EXTENSmON Cords Motor Safety PROTECTmONLa,WARNINGn Electrical Requrements contdCOMBINATmON Square Must be True ACCESSORmESIA WARNINGn Table Insert Compound Minter SAW Terms Cutting Head FIG. D INSTALLINGTHEMITERHANDLEFIG.BSAWBLADEWRENCHFIG.C Forconvenientstorageandpreventionofloss,thereWARN Ne RemovingorinstallingthebladeMiter Scale FIG. J 1Placethehold=downclampassembly1in oneIA WARN,NGn WARNNGnIA Warning Bevel Stop Adjustment FIG. M & NWARN NeI ALiGNiNGTHELASER BeamAvoid Direct EYE Contact Mounting the Miter SAW FIG, O Keepyour Work Area Clean Safety mNSTRUCTmONS for BASmC SAW OPERATmONBefore Using the Miter SAW USE only Recommended AccessoriesAWARNmNG PlanyourworkUsetherighttool. Dontforceatool or Before Leawng the SAW WARNINeBODYANDBANDPOSITIONFIG.P Turning SAW on FIG. QBEVELCUTFIG,S CUTTINGBOWEDMATERIALFIG.U Atanyangle,froma90straightcut0onthescaleCOMPOUNDCUTFIG,T Auxilary Wood Fence FIG. W 4incheshigh Fig+VCuttinga BIJENSIONAL4X4WITHONECUT Fig.X Vertical Miter Cutting FIG. YCutting Base Molding FIG. Z Type of CUT CUTTINGCROWNMOLDINGFIG. AA,BBSawdust LUBRICATmONSAW Guide o MotorParts List for SAW Schematic IA WARIGn10 in. Compound Miter SAW Model no 10 in. Compound Minter SAW Schematic for SAWModel 10 in. Compound LiTER SAWCall anytime, day or night U.S.A. only LoS00-LE-FOYER M888oSU-HOGAR sM Call anytime, day or night U.S.A. and Canada