GENERAL SAFETY mNSTRUCTmONS
BEFORE USmNG THIS POWER TOOL
Safety is a combination of common sense, staying alert and knowing how to use your power tool.
l,&WARNINGn
To avoid mistakes that could cause serious injury, do not plug the too! in unti! you have read and understood the following.
1.READ and become fami{iar with the entire Operators Manual. LEARN the tool'sapplication, limitations and possible hazards.
2.KEEP GUARDS tN PLACE and in working order.
3.REMOVE ADJUSTING KEYS AND WRENCHES. Form the habit of checking to see that keys and adjusting wrenches are removed from the tool before turning ON.
4.KEEP WORK AREA CLEAN Cluttered areas and benches invite accidents.
5.DO NOT USE iN DANGEROUS ENVIRONMENTS. Do not use power tools in damp locations, or expose them to rain or snow. Keep work area well liL
6.KEEP CHILDREN AWAY. All visitors and bystanders should be kept a safe distance from work area.
7.MAKE WORKSHOP CHILD PROOF with padlocks, master switches or by removing starter keys.
8.DO NOT FORCE THE TOOL. It wil! do the job better and safer at the rate for which it was designed.
9.USE THE RIGHT TOOL. Do not force the too! or an attachment to do a job for which it was not designed.
10.USE PROPER EXTENSION CORDS. Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord win result in a drop in line voltage and in loss of power which wil! cause the tool to overheaL The table on page 5 shows the correct size to use depending on cord length and nameplate ampere rating, if in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord.
11 .WEAR PROPER APPAREL Do not wear loose
clothing, gloves, neckties, rings, bracelets, or other jewelry which may get caught in moving parts. Nonslip footwear is recommended. Wear protective hair covering to contain long hair.
12.ALWAYS WEAR EYE PROTECTION Any power too! can throw foreign objects into the eyes and
w_ _o_. could cause permanent eye damage_ ALWAYS wear Safety Goggles (not glasses) that comply with ANSI Safety standard Z87.1 Everyday eyeglasses have only
They ARE NOT safety glasses. Safety Goggles are available at Sears. NOTE: Glasses or goggles not in compliance with ANSI Z87.1 could seriously injure you when they break.
1&WEAR A FACE MASK OR DUST MASK Sawing operation produces dusL
14SECURE WORK. Use clamps or a vise to hold work when practical. It'ssafer than using your hand and it frees both hands to operate the tool
15DISCONNECT TOOLS FROM POWER SOURCE
before servicing, and when changing accessories such as blades, bits and cutters.
16REDUCE THE RiSK OF UNINTENTIONAL STARTING. Make sure switch is in the OFF position before plugging the too! in.
17.USE RECOMMENDED ACCESSORIES. Consutt this
Operator's Manual for recommended accessories. The use of improper accessories may cause risk of injury to yourself or others.
18NEVER STAND ON THE TOOL. Serious injury could occur if the too! is tipped or if the cutting tool is unintentionally contacted_
1&CHECK FOR DAMAGED PARTS. Before further use of the tool, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function
=check for alignment of moving parts, binding of moving parts, breakage of parts, mounting, and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced.
20NEVER LEAVE THE TOOL RUNNING UNATTENDED. TURN THE POWER "OFF". Do not
walk away from a running tool until the blade comes to a complete stop and the tool is unplugged from the powe r sou roe.
21 DO NOT OVERREACH Keep proper footing and balance at al! times.
22.MA_NTAIN TOOLS W_TN CARE. Keep tools sharp and clean for best and safest performance. Follow instructions for lubricating and changing accessories.
2&WARNING: Dust generated from certain materials can be hazardous to your health. Always operate saw in