Craftsman 137.21229 WARN NeI, ALiGNiNGTHELASER Beam, Avoid Direct EYE Contact

Page 14

ALiGNiNGTHELASER BEAM

[A WARNING[

For your own safety, never connect the plug to power source outlet unti[ all the adjustment steps are complete and you have read and understood the safety and operational instructions.

The laser beam must always be correctly aligned with the blade to ensure straight, even cutting.

Your tool is equipped with the Laser Trac® cutting

guide using Class ilia laser beams. The laser beam wilI enable to preview the saw blade path on the stock to be cut before starting the miter saw. This laser guide is powered by the transformed alternating current supply directly through the power lea& The saw must be connected to the power source and the laser on/off switch must be turned on for the laser line to show.

wARN NeI

AVOID DIRECT EYE CONTACT

Loser radiated when [aser guide is turned oil. Avoid direct eye contact° Always un-piug the miter saw from power source before making any adjustments.

NOTE: All the adjustments for the operation of this machine have been completed at the factory. Due to normal wear and use, some occasional readjustments may be necessary.

A. Check Loser Beam Alignment.

1.Mark a 90° straight line across a board to serve as a "pattern line" to test laser alignment. Lay the board on the miter table.

2.Plug saw into outlet and turn on the laser beam and line it up with the pattern line.

3.Lower saw blade to pattern line and if blade is not flush with the pattern line, adjust as follows in procedures (B).

B. Adjusting the Angle of the Laser Trac®(Fig. N-2)

1.Turn the laser element (1) in the desired direction to adjust the laser angle. NOTE: Do not adjust the laser more than _Aturn in either direction as this may damage the laser. There are two flat sides on the laser element where you can position an adjustable wrench for your adjustment.

C. Aligning The Laser Beam

1.Loosen only Y2turn at a time the three set screws (1).

2.Adjust laser by turning the left side set screw clockwise to shift the laser line to the right. To shift the laser line to the left, turn the right side set screws _/2turn at a time.

3.Once alignment of the laser is achieved,

tighten only Y2turn at a time the three set screws

(1)_ Start with the set screw on the left side of the laser assembly, then with the front set screw on the right side of the laser assembly.

Fig. N-1

Laser " 'i

Switch i_

Left Side View

Right Side View

Fig. N-2

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Operators Manuam 10 in. Compound Miter SAW Modem No Sears, Roebuck and Co., Hoffman Estates, IL 60179 USAMotor ONE-YEAR Full Warranty on Craftsman ToolWARNmNG Miter SAWGeneral Safety mNSTRUCTmONS Before USmNG this Power Tool 15DISCONNECT Tools from Power SourceSPECiFiC Safety mNSTRUCTmONS for THiS Compound Minter SAW Electrical Requrements contd Motor Safety PROTECTmONLa,WARNINGn GUmDEUNES for EXTENSmON CordsACCESSORmES COMBINATmON Square Must be TrueIA WARNINGn Table Insert Compound Minter SAW Terms Forconvenientstorageandpreventionofloss,there INSTALLINGTHEMITERHANDLEFIG.BSAWBLADEWRENCHFIG.C Cutting Head FIG. D Removingorinstallingtheblade WARN NeWARNNGn 1Placethehold=downclampassembly1in oneIA WARN,NGn Miter Scale FIG. JBevel Stop Adjustment FIG. M & N IA WarningAvoid Direct EYE Contact WARN NeIALiGNiNGTHELASER Beam Mounting the Miter SAW FIG, O USE only Recommended Accessories Safety mNSTRUCTmONS for BASmC SAW OPERATmONBefore Using the Miter SAW Keepyour Work Area CleanUsetherighttool. Dontforceatool or AWARNmNGPlanyourwork Turning SAW on FIG. Q WARNINeBODYANDBANDPOSITIONFIG.P Before Leawng the SAWCOMPOUNDCUTFIG,T BEVELCUTFIG,S CUTTINGBOWEDMATERIALFIG.UAtanyangle,froma90straightcut0onthescale 4incheshigh Fig+V Auxilary Wood Fence FIG. WCutting Base Molding FIG. Z Cuttinga BIJENSIONAL4X4WITHONECUT Fig.XVertical Miter Cutting FIG. Y CUTTINGCROWNMOLDINGFIG. AA,BB Type of CUTLUBRICATmON SawdustGuide o Motor SAW10 in. Compound Miter SAW Model no Parts List for SAW SchematicIA WARIGn Schematic for SAW 10 in. Compound Minter SAW10 in. Compound LiTER SAW ModelCall anytime, day or night U.S.A. and Canada LoS00-LE-FOYER M888oSU-HOGAR sM Call anytime, day or night U.S.A. only
Top Page Image Contents