Craftsman 137.21236 operating instructions Inserting and Replacing the Laser Batteries FIG. F

Page 13

Fig. E

2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1 3

4

INSERTING AND REPLACING THE LASER BATTERIES (FIG. F)

• Unplug your miter saw.

!WARNING

Failure to unplug your tool could result in

accidental starting causing possible serious personal injury.

1.Remove the locking screw (1) on the battery cover (2) with a Phillips screwdriver, and open the cover.

2.Insert the two supplied AAA batteries in the case as per the diagram below. If replacing the batteries, take out the old batteries and place with new AAA batteries. Dispose of old batteries properly.

3.Put on the battery cover, replace the locking screw and tighten it securely.

NOTE: Replace the batteries with batteries that have a rating of 1.5 volts (Number 4 series and AAA size or equivalent).

Fig. F

AAA Battery

AAA Battery

2

1

REMOVING OR INSTALLING THE BLADE

! WARNING

Only use a 10-inch diameter blade.

To avoid injury from an accidental start, make sure the switch is in the OFF position and plug is not connected to the power source outlet.

Removing Blade (Fig. G, H, I)

1.Unplug the saw from the outlet.

2.Allow the cutting head to rise to the upright position. Raise the lower blade guard (1) to the up position. (Fig. G)

3.Loosen the cover plate screw (2) with a Phillips screwdriver.

4.Rotate the cover plate (3) towards the rear of the tool to expose the arbor bolt (4).

5.Place the blade wrench over the arbor bolt.

Fig. G

1

2

3

4

6.Locate the arbor lock (5) on the motor, below the switch handle. (Fig. H)

7.Press the arbor lock, holding it in firmly while turning the blade wrench clockwise. The arbor lock will engage after turning the wrench. Continue to hold the arbor lock in to keep it engaged, while turning the wrench clockwise to loosen the arbor bolt.

Fig. H

5

8.Remove the arbor bolt (8), outer blade collar (6), and the blade (7). Do not remove the inner blade collar. (Fig. I)

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Sears, Roebuck and Co., Hoffman Estates, IL60179 USA Warranty Table of ContentsProduct Specifications Shown below are some of the symbols you may see SymbolsProhibition Support and Clamp WorkPower Tool Safety Never Leave the Tool Running 24. ! DangerSpecific Safety Instructions for this Compound Miter SAW Compound Miter SAW SafetyKeep the Motor AIR Slots Clean and free of chips or dust Power Supply and Motor SpecificationsGrounding Instructions Electrical Requirements and SafetyAccessories Recommended AccessoriesCarton Contents Know Your Compound Miter SAW Compound Miter SAW Terms Glossary of TermsWoodworking Terms Assembly and Adjustments Inserting and Replacing the Laser Batteries FIG. F Removing or Installing the BladeAdjustment Instructions Installing Blade Fig. G, HAdjusting Fence Squareness FIG. J To Adjust the AngleCutting Arm Downward Travel Adjustment To Adjust the IndicatorBevel Stop Adjustment FIG. M, N, O Cutting ARM TravelMounting the Miter SAW FIG. P, Q Bevel Indicator Fig. NTo avoid injury from unexpected saw movement Mounting instructionsAvoid Direct EYE Contact Laser Guide FIG. REquirements and Safety Before Each USE Inspect Your SAW AdjustmentsKeep Your Work Area Clean OperationWhen SAW is Running Dress for SafetyPlan Your Work Inspect Your WorkpieceTurning SAW on FIG. T Body and Hand Position FIG. SBefore Leaving the SAW Miter CUT FIG. UCompound CUT FIG. W Bevel CUT FIGCutting Base Molding FIG. Y Cutting Bowed Material FIGFig. Z Bevel/Miter SettingsReplacing Carbon Brushes FIG. BB MaintenanceLower Blade Guard Emptying Sawdust BAGProtection Troubleshooting GuideParts List for SAW Schematic Parts List10 in. Compound Miter SAW Model no Schematic for SAWParts List and Schematic for Motor Here’s what the Repair Protection Agreement* includes Repair Protection AgreementsGet it fixed, at your home or ours

137.21236 specifications

The Craftsman 137.21236 is a versatile and reliable tool that caters to both DIY enthusiasts and professional craftsmen alike. Designed to deliver precision and efficiency, this saw embodies the spirit of dependable craftsmanship that the Craftsman brand is known for.

One of the main features of the Craftsman 137.21236 is its robust and powerful motor. With a solid horsepower rating, it provides ample cutting power, making it ideal for a variety of woodworking tasks, including ripping, cross-cutting, and bevel cuts. This powerful motor allows users to effortlessly cut through different materials, including hardwoods, softwoods, and engineered wood products, ensuring versatility in various projects.

Another significant characteristic is its adjustable cutting depth and angle. The saw features a user-friendly bevel mechanism, allowing for precise adjustment of the cutting angle up to 45 degrees. This feature enhances usability when tackling angled cuts, dovetails, or compound miter cuts. Moreover, the cutting depth can be easily modified, enabling users to manage the thickness of the material being worked on, thus providing greater control and flexibility during operation.

The Craftsman 137.21236 also boasts an ergonomically designed handle, which not only improves comfort during extended use but also enhances control and reduces fatigue. The balanced weight distribution of the tool ensures stability, minimizing vibrations during operation for precise cuts.

In terms of safety, this model is equipped with an integrated blade guard and an electric brake, ensuring that it meets the safety standards expected of high-quality power tools. The blade guard prevents accidental contact with the blade, while the electric brake halts the blade's rotation almost instantaneously when the trigger is released, enhancing user safety during operation.

Furthermore, the Craftsman 137.21236 is compatible with a range of blades, allowing users to swap out blades according to the specific needs of their projects. Whether it's a fine-tooth blade for intricate cuts or a carbide-tipped blade for heavy-duty work, the compatibility adds another layer of versatility.

In summary, the Craftsman 137.21236 is a feature-rich and technologically advanced tool that embodies reliability and precision. Its powerful motor, adjustable features, ergonomic design, and focus on safety make it a valuable addition to any workshop, catering to the diverse needs of users, whether they are tackling home renovations or professional woodworking projects.
Top Page Image Contents