Craftsman 137.21236 Bevel Indicator Fig. N, Mounting the Miter SAW FIG. P, Q

Page 16

90° Bevel Indicator (Fig. N)

1.When the blade is exactly 90° to the table, loosen the bevel indicator screw (5) using a #2 Phillips screwdriver.

2.Adjust bevel indicator (6) to the “0” mark (7) on the bevel scale and retighten the screw.

Fig. N

6 7

5

45° Bevel Adjustment (Fig. O)

1.Unlock the bevel lock handle (1) and tilt the cutting arm as far to the left as possible.

2.Using a combination square, check to see if the blade angle is 45° to the table.

3.If the blade is not at 45° to the miter table, tilt the cutting arm to the right, loosen the locknut (5) on the bevel angle adjustment bolt (4) and use a 13 mm wrench to adjust the bolt (4) in or out to increase or decrease the bevel angle.

4.Tilt the cutting arm to the left to 45° bevel and recheck for alignment.

5.Repeat steps 1 through 4 until the blade is at 45° to the miter table.

6.Tighten bevel lock handle and locknut (5) when alignment is achieved.

Fig. O

1

4 5

MOUNTING THE MITER SAW (FIG. P, Q)

! WARNING

To avoid injury from unexpected saw movement:

●Before moving the saw, disconnect the power cord from the outlet, and lock the cutting arm in the lower position using the stop latch.

NOTE: The stop latch is for carrying or storing the tool. It is not to be used for holding the saw while cutting. Lower blade and press in stop latch to secure saw for transport or storage.

●Never carry the miter saw by the power cord or by the switch handle. Carrying the tool by the power cord could cause damage to the insulation or wire connections resulting in electric shock or fire.

●To avoid injury from flying debris, do not allow visitors to stand behind the saw.

●Place the saw on a firm, level work-surface where there is room for handling and properly supporting the workpiece.

●Support the saw on a level work surface.

●Bolt or clamp the saw to its support.

Place the saw in the desired location, either on a work bench or recommended leg set. The base of the saw has four mounting holes (10). (Fig. P)

Mounting instructions

1.For stationary use, place the saw in the desired location, directly on a workbench where there is room for handling and proper support of the workpiece. The base of the saw has four mounting holes. Bolt the base of the miter saw (1) to the work surface (5), using the fastening method as shown in Fig P.

Fig. P

1.

Miter saw base

 

2

2.

Hex head bolt

 

 

3

3.

Rubber washer

4

 

4.

Flat washer

 

1

 

5.

Workbench

 

 

 

6.

Flat washer

5

 

7.

Lockwasher

 

8.

Hex nut

6

 

9.

Jam nut

8

7

 

10

 

9

 

 

 

10

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Sears, Roebuck and Co., Hoffman Estates, IL60179 USA Warranty Table of ContentsProduct Specifications Symbols Shown below are some of the symbols you may seeProhibition Support and Clamp WorkPower Tool Safety 24. ! Danger Never Leave the Tool RunningCompound Miter SAW Safety Specific Safety Instructions for this Compound Miter SAWKeep the Motor AIR Slots Clean and free of chips or dust Power Supply and Motor SpecificationsElectrical Requirements and Safety Grounding InstructionsRecommended Accessories AccessoriesCarton Contents Know Your Compound Miter SAW Compound Miter SAW Terms Glossary of TermsWoodworking Terms Assembly and Adjustments Removing or Installing the Blade Inserting and Replacing the Laser Batteries FIG. FInstalling Blade Fig. G, H Adjustment InstructionsAdjusting Fence Squareness FIG. J To Adjust the AngleTo Adjust the Indicator Cutting Arm Downward Travel AdjustmentBevel Stop Adjustment FIG. M, N, O Cutting ARM TravelBevel Indicator Fig. N Mounting the Miter SAW FIG. P, QTo avoid injury from unexpected saw movement Mounting instructionsLaser Guide FIG. R Avoid Direct EYE ContactAdjustments Equirements and Safety Before Each USE Inspect Your SAWKeep Your Work Area Clean OperationDress for Safety When SAW is RunningPlan Your Work Inspect Your WorkpieceBody and Hand Position FIG. S Turning SAW on FIG. TBefore Leaving the SAW Miter CUT FIG. UBevel CUT FIG Compound CUT FIG. WCutting Base Molding FIG. Y Cutting Bowed Material FIGBevel/Miter Settings Fig. ZMaintenance Replacing Carbon Brushes FIG. BBLower Blade Guard Emptying Sawdust BAGTroubleshooting Guide ProtectionParts List Parts List for SAW SchematicSchematic for SAW 10 in. Compound Miter SAW Model noParts List and Schematic for Motor Repair Protection Agreements Here’s what the Repair Protection Agreement* includesGet it fixed, at your home or ours

137.21236 specifications

The Craftsman 137.21236 is a versatile and reliable tool that caters to both DIY enthusiasts and professional craftsmen alike. Designed to deliver precision and efficiency, this saw embodies the spirit of dependable craftsmanship that the Craftsman brand is known for.

One of the main features of the Craftsman 137.21236 is its robust and powerful motor. With a solid horsepower rating, it provides ample cutting power, making it ideal for a variety of woodworking tasks, including ripping, cross-cutting, and bevel cuts. This powerful motor allows users to effortlessly cut through different materials, including hardwoods, softwoods, and engineered wood products, ensuring versatility in various projects.

Another significant characteristic is its adjustable cutting depth and angle. The saw features a user-friendly bevel mechanism, allowing for precise adjustment of the cutting angle up to 45 degrees. This feature enhances usability when tackling angled cuts, dovetails, or compound miter cuts. Moreover, the cutting depth can be easily modified, enabling users to manage the thickness of the material being worked on, thus providing greater control and flexibility during operation.

The Craftsman 137.21236 also boasts an ergonomically designed handle, which not only improves comfort during extended use but also enhances control and reduces fatigue. The balanced weight distribution of the tool ensures stability, minimizing vibrations during operation for precise cuts.

In terms of safety, this model is equipped with an integrated blade guard and an electric brake, ensuring that it meets the safety standards expected of high-quality power tools. The blade guard prevents accidental contact with the blade, while the electric brake halts the blade's rotation almost instantaneously when the trigger is released, enhancing user safety during operation.

Furthermore, the Craftsman 137.21236 is compatible with a range of blades, allowing users to swap out blades according to the specific needs of their projects. Whether it's a fine-tooth blade for intricate cuts or a carbide-tipped blade for heavy-duty work, the compatibility adds another layer of versatility.

In summary, the Craftsman 137.21236 is a feature-rich and technologically advanced tool that embodies reliability and precision. Its powerful motor, adjustable features, ergonomic design, and focus on safety make it a valuable addition to any workshop, catering to the diverse needs of users, whether they are tackling home renovations or professional woodworking projects.
Top Page Image Contents