Craftsman 137.21236 Maintenance, Replacing Carbon Brushes FIG. BB, Lower Blade Guard

Page 23

MAINTENANCE

MAINTENANCE

!DANGER

To avoid injury, never put lubricants on the blade while it is spinning.

!WARNING

To avoid fire or toxic reaction, never use gasoline, naphtha acetone, lacquer thinner or similar highly volatile solvents to clean the miter saw.

!WARNING

To avoid injury from unexpected starting or electrical shock, unplug the power cord before working on the saw.

!WARNING

For your safety, this saw is double-insulated. To avoid electrical shock, fire or injury, use only parts identical to those identified in the parts list. Reassemble exactly as the original assembly to avoid electrical shock.

REPLACING CARBON BRUSHES (FIG. BB)

Replace both carbon brushes when either has less than 1/4 in. length of carbon remaining, or if the spring or wire is damaged or burned. To inspect or replace brushes, first unplug the saw. Then remove the black plastic cap (1) on the side of the motor (2). Remove the cap cautiously, because it is springloaded. Then pull out the brush and replace. Replace for the other side. To reassemble reverse the procedure. The ears on the metal end of the assembly go in the same hole the carbon part fits into. Tighten the cap snugly, but do not overtighten.

NOTE: To reinstall the same brushes, first make sure the brushes go back in exactly the way they came out. This will avoid a break-in period that reduces motor performance and increases wear.

Fig. BB

1

LOWER BLADE GUARD

Do not use the saw without the lower blade guard. The lower blade guard is attached to the saw for your protection. Should the lower guard become damaged, do not use the saw until the damaged guard has been replaced. Develop a regular check to make sure the lower guard is working properly. Clean the lower guard of any dust or buildup with a damp cloth.

CAUTION: Do not use solvents on the guard. They could make the plastic “cloudy” and brittle.

!WARNING

When cleaning the lower guard, unplug the saw from the power source receptacle to avoid unexpected startup.

EMPTYING SAWDUST BAG

Periodically, sawdust will accumulate under the work table and base. This could cause difficulty in the movement of the worktable when setting up a miter cut. Frequently blow out or vacuum up the sawdust.

!WARNING

If blowing sawdust, wear proper eye protection to keep debris from blowing into eyes.

LUBRICATION (FIG. CC)

All the motor bearings in this tool are lubricated with a sufficient amount of high grade lubricant for the life of the unit under normal operating conditions; therefore, no further bearing lubrication is required.

Lubricate the following as necessary:

Chop pivot: Apply light machine oil to points indicated in illustration.

Chop and Central pivot: Apply light machine oil to points indicated in illustration.

Fig. CC

Central pivot of plastic guard

Chop pivot

2

23

Image 23
Contents Sears, Roebuck and Co., Hoffman Estates, IL60179 USA Product Specifications Table of ContentsWarranty Support and Clamp Work SymbolsShown below are some of the symbols you may see ProhibitionPower Tool Safety Never Leave the Tool Running 24. ! DangerPower Supply and Motor Specifications Compound Miter SAW SafetySpecific Safety Instructions for this Compound Miter SAW Keep the Motor AIR Slots Clean and free of chips or dustGrounding Instructions Electrical Requirements and SafetyAccessories Recommended AccessoriesCarton Contents Know Your Compound Miter SAW Woodworking Terms Glossary of TermsCompound Miter SAW Terms Assembly and Adjustments Inserting and Replacing the Laser Batteries FIG. F Removing or Installing the BladeTo Adjust the Angle Installing Blade Fig. G, HAdjustment Instructions Adjusting Fence Squareness FIG. JCutting ARM Travel To Adjust the IndicatorCutting Arm Downward Travel Adjustment Bevel Stop Adjustment FIG. M, N, OMounting instructions Bevel Indicator Fig. NMounting the Miter SAW FIG. P, Q To avoid injury from unexpected saw movementAvoid Direct EYE Contact Laser Guide FIG. ROperation AdjustmentsEquirements and Safety Before Each USE Inspect Your SAW Keep Your Work Area CleanInspect Your Workpiece Dress for SafetyWhen SAW is Running Plan Your WorkMiter CUT FIG. U Body and Hand Position FIG. STurning SAW on FIG. T Before Leaving the SAWCutting Bowed Material FIG Bevel CUT FIGCompound CUT FIG. W Cutting Base Molding FIG. YFig. Z Bevel/Miter SettingsEmptying Sawdust BAG MaintenanceReplacing Carbon Brushes FIG. BB Lower Blade GuardProtection Troubleshooting GuideParts List for SAW Schematic Parts List10 in. Compound Miter SAW Model no Schematic for SAWParts List and Schematic for Motor Here’s what the Repair Protection Agreement* includes Repair Protection AgreementsGet it fixed, at your home or ours

137.21236 specifications

The Craftsman 137.21236 is a versatile and reliable tool that caters to both DIY enthusiasts and professional craftsmen alike. Designed to deliver precision and efficiency, this saw embodies the spirit of dependable craftsmanship that the Craftsman brand is known for.

One of the main features of the Craftsman 137.21236 is its robust and powerful motor. With a solid horsepower rating, it provides ample cutting power, making it ideal for a variety of woodworking tasks, including ripping, cross-cutting, and bevel cuts. This powerful motor allows users to effortlessly cut through different materials, including hardwoods, softwoods, and engineered wood products, ensuring versatility in various projects.

Another significant characteristic is its adjustable cutting depth and angle. The saw features a user-friendly bevel mechanism, allowing for precise adjustment of the cutting angle up to 45 degrees. This feature enhances usability when tackling angled cuts, dovetails, or compound miter cuts. Moreover, the cutting depth can be easily modified, enabling users to manage the thickness of the material being worked on, thus providing greater control and flexibility during operation.

The Craftsman 137.21236 also boasts an ergonomically designed handle, which not only improves comfort during extended use but also enhances control and reduces fatigue. The balanced weight distribution of the tool ensures stability, minimizing vibrations during operation for precise cuts.

In terms of safety, this model is equipped with an integrated blade guard and an electric brake, ensuring that it meets the safety standards expected of high-quality power tools. The blade guard prevents accidental contact with the blade, while the electric brake halts the blade's rotation almost instantaneously when the trigger is released, enhancing user safety during operation.

Furthermore, the Craftsman 137.21236 is compatible with a range of blades, allowing users to swap out blades according to the specific needs of their projects. Whether it's a fine-tooth blade for intricate cuts or a carbide-tipped blade for heavy-duty work, the compatibility adds another layer of versatility.

In summary, the Craftsman 137.21236 is a feature-rich and technologically advanced tool that embodies reliability and precision. Its powerful motor, adjustable features, ergonomic design, and focus on safety make it a valuable addition to any workshop, catering to the diverse needs of users, whether they are tackling home renovations or professional woodworking projects.