Craftsman 113.2472T0 owner manual Blade Guide Gullet Backup Bearing

Page 21

2.Turn the upper wheel by hand a few times and notice if the blade remains in the center of the tire

on the top wheel.

If the blade moves away from the center of the tire while you are turning it, the blade is not tracking properly.

The top wheel shaft is hinged so the blade can be tracked. Tilt the wheel by turning the tracking adjustment screw using a medium screw driver. (See illustration.)

a. If the blade moves toward the front of the band

saw:

Turn the tracking adjustment screw clockwise about 1/4 of a turn, as though you were

tightening it.

b. If the blade moves toward the back of the band

saw:

Turn the tracking adjustment screw counter- clockwise about 1/4 of a turn as though you were loosening it.

c. Check adjustment byturning wheel by hand a few times. Repeat adjustment if necessary.

3.The upper and lower blade guides support the blade and keep it from twisting during operation. Adjust blade guide support whenever blades are changed or replaced with a different width.

4.Push the blade guide support toward the blade and adjust the blade guides so they are about 1/32-inch from the deepest part of the blade teeth. This deep part is called a gullet. Tighten the set screw locking the blade guide support.

Turn the upper wheel, by hand, checking the position of the blade guide support.

NOTE: Letting the blade teeth hit the blade guides while using the band saw will ruin the blade. The set of the teeth and the sharpened edge of the teeth would be damaged. Proper adjustment of the upper and lower blade guide assemblies will prevent this from happening.

Repeat procedure for lower blade guide support.

5.Slide the two blade guides evenly against the sides of the blade. Do not push the blade guides or pinch the blade guides against the blade. Rotate the upper wheel by hand so the blade travels downward. This leaves proper space for blade. Make sure one guide is not further from

the blade than the other. Tighten both setscrews with a 1/8-inch hex "L" wrench. Repeat proce- dure for lower blade guides.

NOTE: The backup bearings support the blade from the rear and will spin when the blade is pushed against them while you are cutting. As

soon as you stop cutting, the bearings should stop spinning.

TRACKING ADJUSTMENT SCREW

BLADE GUIDE

GULLET

BLADE

BACKUP BEARING

BLADE GUIDE

BLADE GUIDE

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Crrftsmrn Know Your Power Tool Ground ALL Tools Full ONE Year Warranty on Craftsman Band SAWKeep Work Area Clean USE Recommended Accessories Never Stand on ToolBefore Using the SAW Additional safety instructions for band sawWhen Installing or Moving the SAW Before Each USEAccessories Before SandingWhenever SAW is Running Glossary of terms for woodworking Table of contentsPower Supply Motor Safety ProtectionModel NO.MODEL no Unpacking and checking contents One carton and includes steel legs Table of Loose PartsList of Loose Parts in BAG #507655 List of Loose Parts in BAG #507657Description QTY List of Loose Parts in BAG #507755Assembly and alignment Assembling LEG SETWare Assembling Cabinet EASKI. .T Mounting the Motor Flanged Belttensioningis doneby tighteningthe wing Connecting the MotorMounting the SAW to the LEG SET Mounting the SAW to the CabinetFrom loose parts bag find the following hard- ware Attaching Trim Caps & Trim Ledge Attaching the HandwheelGetting to Know Your Band SAW Location and function of controlsUpperblade Installing the BladeAligning the Blade and Blade Guide Assemblies Blade Guide Gullet Backup Bearing LAD E Mounting the Front TableTable Leveling Setscrews Squaring the Blade to the Table ON-OFF Switch Adjusting Bevel Lock KnobTilting Head for Bevel CUT Circle Cutting Basic band saw operationBlade Size InchesSawdust Collection Installing Sanding AttachmentInstalling the Sanding Belt Recommended accessoriesMaintenance Adjusting Band SAW Bevel TravelAdjusting the Upper Blade Guide Travel Trouble shooting Outlet Before Trouble Shooting Your Band SAW/SANDERProbable Cause Remedy Trouble Shooting -- Motor TroubleProbable Cause Models 113.247210 Parts List for Craftsman 12-INCH Band SawsParts List for Craftsman 12-INCH Band Saws Always order by Part Number Not by Key NumberKey Part Description Parts List for Craftsman 12-INCH Band Saws Base Components Parts List for Craftsman 12-1NCH Band Saws26 \ Bevel Drive and Motor Mount Assembly Parts Always order by Part Number Not by Key Number Description Parts List for Craftsman 12 Band SAWParts UST LEG SET Band SAW with Cabinet Band SAW with LEG SETPartnumber Partdescription

113.2472T0 specifications

The Craftsman 113.2472T0 is a benchtop table saw that stands out for its solid construction and versatile functionality, making it a favorite among both professional woodworkers and DIY enthusiasts. Its performance is bolstered by a robust 15-amp motor, providing enough power to handle various cutting tasks effectively. This motor allows the saw to deliver up to 5,000 RPM, ensuring clean and efficient cuts through different types of wood materials.

One of the main features of the Craftsman 113.2472T0 is its precision and accuracy. It comes equipped with a reliable rip fence system that can be easily adjusted for accurate cuts. The fence locks securely in place, reducing the likelihood of misalignment during use. Additionally, the saw includes a 10-inch carbide-tipped blade, which not only enhances durability but also improves cutting efficiency. The blade can be angled for precise bevel cuts, extending the tool's versatility for various woodworking projects.

Safety is a paramount concern in any workshop, and the Craftsman 113.2472T0 integrates several safety features to protect its users. The blade guard system not only shields the user from potential hazards but also allows for easy visibility of the cutting area. A push stick is included, enabling safe handling of smaller workpieces. Furthermore, the saw’s base is designed to provide stability, reducing vibration and ensuring a safe working environment.

In terms of portability, the Craftsman 113.2472T0 is designed with user convenience in mind. It features a compact design, which makes it easy to transport and store, whether in a dedicated workshop or a makeshift setup. The onboard storage for accessories keeps everything organized and within reach, streamlining the woodworking process.

The table itself is constructed from high-quality materials, offering excellent support and a smooth surface for woodworking tasks. With extensions available, the table size can be increased to accommodate larger materials, making it suitable for bigger projects. Overall, the Craftsman 113.2472T0 combines power, precision, and portability, making it an outstanding option for anyone needing a reliable and versatile table saw in their woodworking arsenal.
Top Page Image Contents