Craftsman 113.2472T0 owner manual Mounting the Front Table, Lad E

Page 22

6.To insure the backup bearing is properly sup- porting the blade, push the bearing toward the blade until it almost touches it. Turn the upper

wheel, by hand, checking the backup bearing to make sure it is not turning. If the bearing is

turning the blade is too close. Move bearing slightly away from blade and tighten set screw with 1/8" hex "L" wrench. Turn upper wheel and recheck the bearing. Adjust again if necessary.

7.Repeat procedure for lower backup bearing.

8.Turn upper wheel by hand and check the blade guides and backup bearings to make sure they are adjusted correctly. Make any readjustments if necessary.

9.Install blade guard and tighten with phillips screwdriver. (See illustration, page 19.)

10.Install the front cover. Rest top edge of cover on two latch springs along the top edge of back cover. Swing cover down into position, engaging the three other latch springs. Push the front cover into position on the back cover. Check that the lip on the front cover completely overlaps the lip on the rear cover.

MOUNTING THE FRONT TABLE

1. Turn front table over. Locate the two (2) latch springs, two (2) alignment springs, and the four

(4)1/4-20 x 5/8 hex washer head thread forming screws.

2:Install the two latch springs on the front table as illustrated using a 3/8-inch wrench or socket.

Install the two alignment springs on the front table as illustrated using a 3/8-inch wrench or socket.

3.Locate the two (2) oval point setscrews 1/4-20 x 1/2 and use an 1/8-inch hex "L" wrench to install

in the two holes, as illustrated, but do not allow the screws to extend beyond the underside of the table.

 

'4''"'--"

B LAD E

I

I

z i

F

BACKUP BEARIING

I

"1

"1

z

J

I

FRONT COVER

SPRING

_114-20 x 5/8

_"*-."_--- WASHER HEAD

SCREW

...-.L =i_-_'''''_ALIGNMENT

"'_T

_'_..._

 

 

SPRING

 

',

I

_

LATCH SPRING

,../HEX"L"WRENCH

j.l/4-20X1/2

I _ OVAL pOINT

ySETSCREW

FRONT TABLE

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Crrftsmrn Keep Work Area Clean Full ONE Year Warranty on Craftsman Band SAWKnow Your Power Tool Ground ALL Tools USE Recommended Accessories Never Stand on ToolWhen Installing or Moving the SAW Additional safety instructions for band sawBefore Using the SAW Before Each USEBefore Sanding AccessoriesWhenever SAW is Running Table of contents Glossary of terms for woodworkingMotor Safety Protection Power SupplyModel NO.MODEL no Unpacking and checking contents Table of Loose Parts One carton and includes steel legsDescription QTY List of Loose Parts in BAG #507657List of Loose Parts in BAG #507655 List of Loose Parts in BAG #507755Assembling LEG SET Assembly and alignmentWare Assembling Cabinet EASKI. .T Mounting the Motor Flanged Connecting the Motor Belttensioningis doneby tighteningthe wingMounting the SAW to the Cabinet Mounting the SAW to the LEG SETFrom loose parts bag find the following hard- ware Attaching the Handwheel Attaching Trim Caps & Trim LedgeLocation and function of controls Getting to Know Your Band SAWInstalling the Blade UpperbladeAligning the Blade and Blade Guide Assemblies Blade Guide Gullet Backup Bearing Mounting the Front Table LAD ETable Leveling Setscrews Squaring the Blade to the Table Adjusting Bevel Lock Knob ON-OFF SwitchTilting Head for Bevel CUT Blade Size Basic band saw operationCircle Cutting InchesInstalling Sanding Attachment Sawdust CollectionRecommended accessories Installing the Sanding BeltAdjusting Band SAW Bevel Travel MaintenanceAdjusting the Upper Blade Guide Travel Outlet Before Trouble Shooting Your Band SAW/SANDER Trouble shootingProbable Cause Remedy Trouble Trouble Shooting -- MotorProbable Cause Parts List for Craftsman 12-INCH Band Saws Models 113.247210Always order by Part Number Not by Key Number Parts List for Craftsman 12-INCH Band SawsKey Part Description Parts List for Craftsman 12-INCH Band Saws Parts List for Craftsman 12-1NCH Band Saws Base Components26 \ Bevel Drive and Motor Mount Assembly Parts Parts List for Craftsman 12 Band SAW Always order by Part Number Not by Key Number DescriptionParts UST LEG SET Partnumber Band SAW with LEG SETBand SAW with Cabinet Partdescription

113.2472T0 specifications

The Craftsman 113.2472T0 is a benchtop table saw that stands out for its solid construction and versatile functionality, making it a favorite among both professional woodworkers and DIY enthusiasts. Its performance is bolstered by a robust 15-amp motor, providing enough power to handle various cutting tasks effectively. This motor allows the saw to deliver up to 5,000 RPM, ensuring clean and efficient cuts through different types of wood materials.

One of the main features of the Craftsman 113.2472T0 is its precision and accuracy. It comes equipped with a reliable rip fence system that can be easily adjusted for accurate cuts. The fence locks securely in place, reducing the likelihood of misalignment during use. Additionally, the saw includes a 10-inch carbide-tipped blade, which not only enhances durability but also improves cutting efficiency. The blade can be angled for precise bevel cuts, extending the tool's versatility for various woodworking projects.

Safety is a paramount concern in any workshop, and the Craftsman 113.2472T0 integrates several safety features to protect its users. The blade guard system not only shields the user from potential hazards but also allows for easy visibility of the cutting area. A push stick is included, enabling safe handling of smaller workpieces. Furthermore, the saw’s base is designed to provide stability, reducing vibration and ensuring a safe working environment.

In terms of portability, the Craftsman 113.2472T0 is designed with user convenience in mind. It features a compact design, which makes it easy to transport and store, whether in a dedicated workshop or a makeshift setup. The onboard storage for accessories keeps everything organized and within reach, streamlining the woodworking process.

The table itself is constructed from high-quality materials, offering excellent support and a smooth surface for woodworking tasks. With extensions available, the table size can be increased to accommodate larger materials, making it suitable for bigger projects. Overall, the Craftsman 113.2472T0 combines power, precision, and portability, making it an outstanding option for anyone needing a reliable and versatile table saw in their woodworking arsenal.
Top Page Image Contents