Maintenance, Adjusting Band SAW Bevel Travel

maintenance

WARNING: FOR YOUR OWN SAFETY, TURN SWITCH "OFF" AND REMOVE PLUG FROM POWER

SOURCE OUTLET BEFORE MAINTAINING OR LUBRICATING YOUR BAND SAW.

Tires

Pitch and sawdust that build up on the tires should be removed with a stiff brush or scraped off with a piece of wood.

CAUTION: To avoid damaging the tires do not use a sharp knife or any kind of solvent.

When the tires become worn they should be replaced. When replacing the tires, stretch them around the wheels but do not glue them on.

ADJUSTING BAND SAW BEVEL TRAVEL

If the band saw will not hold its position when at a bevel angle, and before the bevel lock is locked, or if it is difficult to change the bevel angle, an adjustment

is necessary to correct the force required to bevel the band saw.

To adjust the force required to bevel the band saw, locate the three (3) capscrews holding the frame to the motor mount. The capscrews are located in the recessed area behind the hub of the lower wheel at the 2 o'clock, 6 o'clock, and 10 o'clock positions. Use a 3!16-inch hexagonal "L" wrench that has a 4-inch leg, reach between the spokes of the lower wheel to

the capscrews. Adjust the capscrews equally until the bevel action is smooth and the saw will hold its

position before the bevel lock is locked.

ADJUSTING THE UPPER BLADE GUIDE TRAVEL

If the upper guide bar will not move up and down easily or falls when the lock knob is loosened, the following adjustment should be performed.

1.Remove the Guide Bar Lock Knob and the washer which is under it.

2.Using a 7/16" socket or wrench, tighten the nut which is under the washer to just tight.

3.Then loosen the same nut 1 turn.

4.Move the guide bar up and down to check for smooth movement while still holding its position

when released.

5.Make further adjustments to the nut as required to get the guide bar to move smoothly and hold its position when released.

6.Reinstall the washer and Guide Bar Lock Knob.

General Maintenance

Keep your band saw clean. Remove the sawdust from the inside. Vacuum or blow out frequently,

Do not allow filth to build up on the table, the guides orthe back-up bearings. Clean them with Craftsman

Gum and Pitch Remover.

CAUTION: Do not immerse the backup bearings in the gum and pitch remover.

Put a thin coat of paste wax on the table so that the wood slides easily while cutting.

Light Bulb

To replace the light bulb remove the front cover, Use a phillips screwdriver to remove the lens and replace the bulb. The light bulb is a 25 watt bayonet mount bulb.

Motor

Frequently blow or vacuum out any sawdust from the motor. Follow lubrication instruction on the motor label.

WARNING: TO AVOID EYE INJURY FROM BLOW-

ING DEBRIS, WEAR SAFETY GOGGLES WHEN BLOWING OUT SAWDUST.

WARNING: TO AVOID ELECTROCUTION OR FIRE,

IMMEDIATELY REPLACE A WORN, CUT, OR DAMAGED POWER CORD.

Lubrication

All of the ball bearings are packed with grease at the factory. They require no further lubrication.

WIRE CONNECTOR
		BLACK
SWITCH	(3 REQ)---_	CORD
		CORD
BLACK		BLACK

CORD W/PLUG

GRE

CORD

BLACK

WIRING DIAGRAM

113.2472T0 specifications

The Craftsman 113.2472T0 is a benchtop table saw that stands out for its solid construction and versatile functionality, making it a favorite among both professional woodworkers and DIY enthusiasts. Its performance is bolstered by a robust 15-amp motor, providing enough power to handle various cutting tasks effectively. This motor allows the saw to deliver up to 5,000 RPM, ensuring clean and efficient cuts through different types of wood materials.

One of the main features of the Craftsman 113.2472T0 is its precision and accuracy. It comes equipped with a reliable rip fence system that can be easily adjusted for accurate cuts. The fence locks securely in place, reducing the likelihood of misalignment during use. Additionally, the saw includes a 10-inch carbide-tipped blade, which not only enhances durability but also improves cutting efficiency. The blade can be angled for precise bevel cuts, extending the tool's versatility for various woodworking projects.

Safety is a paramount concern in any workshop, and the Craftsman 113.2472T0 integrates several safety features to protect its users. The blade guard system not only shields the user from potential hazards but also allows for easy visibility of the cutting area. A push stick is included, enabling safe handling of smaller workpieces. Furthermore, the saw’s base is designed to provide stability, reducing vibration and ensuring a safe working environment.

In terms of portability, the Craftsman 113.2472T0 is designed with user convenience in mind. It features a compact design, which makes it easy to transport and store, whether in a dedicated workshop or a makeshift setup. The onboard storage for accessories keeps everything organized and within reach, streamlining the woodworking process.

The table itself is constructed from high-quality materials, offering excellent support and a smooth surface for woodworking tasks. With extensions available, the table size can be increased to accommodate larger materials, making it suitable for bigger projects. Overall, the Craftsman 113.2472T0 combines power, precision, and portability, making it an outstanding option for anyone needing a reliable and versatile table saw in their woodworking arsenal.