Stow SHS62A CUT-OFF SAW Maintenance, V-belt should remain in tension, Tensioning position

Page 22

SHS62A CUT-OFF SAW — MAINTENANCE

V-Belt Changing Procedure (continued)

Re-tension the V-belt by turning the belt tensioning cam		.
The V-belt should remain in tension.
Fully tighten the three nuts	that lock the V-belt into the proper
tensioning position.

Figure 18. Reversing the Cutting Arm


Re-install the guard	and V-belt	covers. Fully tighten
the two cap screws	and reinstall the adjustment knob		.

N

Figure 19. Re-Installing Cover Guard

PAGE 22 — SHS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (06/02/06)

Image 22

Contents SideWinder Page Page SHS62A CUT-OFF SAW Table of Contents SHS62A CUT-OFF SAW Parts Ordering Procedures SHS62A CUT-OFF SAW Safety Message Alert Symbols Always wear approved eye and hearing protection SHS62A CUT-OFF SAW Safety Message Alert SymbolsRotating blade can cut and crush. Keep hands and feet clear SHS62A CUT-OFF SAW Rules for Safe Operation General Safety SHS62A CUT-OFF SAW Rules for Safe OperationSaw Transportation Safety Diamond Blade SafetyNever use carbide-tipped or toothed type blades of any kind SHS62A CUT-OFF SAW Rules for Safe Operation Always know the location of the nearest first aid kitEngine Type DisplacementDimensions LxWxH Engine Speed 10,000SHS62A CUT-OFF SAW Decal Placement Machine Operation And Safety Decals10 9 8 7 6 SHS62A CUT-OFF SAW Controls & Components SHS62A CUT-OFF SAW Blade Installation Instructions Blade shaftSHS62A CUT-OFF SAW Water KIT Installation Instructions Fasten the clamp to the Roller Bar Support ArmSHS62A CUT-OFF SAW Blades Diamond BladeFuel Check Place the engine ON/OFF switch in the on positionSHS62A CUT-OFF SAW Initial START-UP/OPERATION StartingSHS62A CUT-OFF SAW Initial START-UP/OPERATION Shut-downCover Guard Belt Changing ProcedureKnob Until the V-belt is completely slackedV-belt should remain in tension SHS62A CUT-OFF SAW MaintenanceRe-install the guard Tensioning positionReversing the Cutting Arm Procedure Cam .The V-belt should remain in tension Re-attach the cover guardSHS62A CUT-OFF SAW Maintenance AIR/FUEL Filter Air/Fuel Filter Maintenance ProceduresSHS62A CUT-OFF SAW Troubleshooting Blade SHS62A CUT-OFF SAW Troubleshooting Engine Troubleshooting EngineTroubleshooting Engine Spark plug heat value improper?SHS62A CUT-OFF SAW Filter Kits Includes 1 eaPart NO. Column SHS62A CUT-OFF SAW Explanation of Parts Section RemarksNO. Column QTY. ColumnSHS62A CUT-OFF SAW Suggested Spare Parts To 3 UnitsSHS62A CUT-OFF SAW Muffler Assy Part Name SHS62A CUT-OFF SAW Recoil Start Assy HANDLE, Starter Rope SHS62A CUT-OFF SAW Crankcase Assy Plate SHS62A CUT-OFF SAW V-BELT Cover Clutch Side Assy SHS62A CUT-OFF SAW V-BELT Cover Clutch Side Assy SHS62A CUT-OFF SAW V-BELT Cover Pulley /BLADE Guard Part Name QTY SHS62A CUT-OFF SAW Fuel Tank Assy Part Name QTY Remarks SHS62A CUT-OFF SAW Lifting Handle and Roller Assy SHS62A CUT-OFF SAW Lifting Handle and Roller Assy SHS62A CUT-OFF SAW -THROTTLE Linkage Assy Spring SHS62A CUT-OFF SAW Flywheel Cover Assy WASHER, Flat SHS62A CUT-OFF SAW Flywheel Assy Pawl SET SHS62A CUT-OFF SAW Ignition Coil Assy Spring Spark Plug SHS62A CUT-OFF SAW AIR Filter Assy FLANGE, PRE- FILTER, CAP SHS62A CUT-OFF SAW Carburetor Mounting Assy Carburetor Mounting Assy SHS62A CUT-OFF SAW Carburetor Assy Throttle Shaft SHS62A CUT-OFF SAW Crankshaft / Piston Assy SHS62A CUT-OFF SAW Crankshaft and Piston Assy SHS62A CUT-OFF SAW Water KIT Assy VALVE, SHUT-OFF SHS62A CUT-OFF SAW Tools HS4191240 00325Recommended Diamond Blades For Your Side Winder Saw SHS62A CUT-OFF SAW Recommended Diamond BladesTerms and Conditions of Sale Terms and Conditions of Sale PartsHeres HOW to GET Help