Stow SHS62A manual Cam .The V-belt should remain in tension, Re-attach the cover guard

Page 24

SHS62A CUT-OFF SAW — MAINTENANCE

Reversing the Cutting Arm Procedure (continued)

Reverse the cutting arm 180 degrees as shown in the Figure 23, and re-tension the V-belt by turning the belt tensioning

cam .The V-belt should remain in tension.

Fully tighten the three nuts	that lock the V-belt into the proper
tensioning position.

Figure 23. Reversing the Cutting Arm


Re-attach the cover guard	with the 2 cap screws		,
and reconnect the guard adjustment knob		.

Figure 24. Re-attaching Cover Guard

PAGE 24 — SHS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (06/02/06)

Image 24

Contents SideWinder Page Page SHS62A CUT-OFF SAW Table of Contents SHS62A CUT-OFF SAW Parts Ordering Procedures SHS62A CUT-OFF SAW Safety Message Alert Symbols SHS62A CUT-OFF SAW Safety Message Alert Symbols Always wear approved eye and hearing protectionRotating blade can cut and crush. Keep hands and feet clear SHS62A CUT-OFF SAW Rules for Safe Operation General Safety SHS62A CUT-OFF SAW Rules for Safe OperationDiamond Blade Safety Saw Transportation SafetyNever use carbide-tipped or toothed type blades of any kind SHS62A CUT-OFF SAW Rules for Safe Operation Always know the location of the nearest first aid kitDisplacement Dimensions LxWxHEngine Type Engine Speed 10,000SHS62A CUT-OFF SAW Decal Placement Machine Operation And Safety Decals10 9 8 7 6 SHS62A CUT-OFF SAW Controls & Components SHS62A CUT-OFF SAW Blade Installation Instructions Blade shaftSHS62A CUT-OFF SAW Water KIT Installation Instructions Fasten the clamp to the Roller Bar Support ArmSHS62A CUT-OFF SAW Blades Diamond BladePlace the engine ON/OFF switch in the on position SHS62A CUT-OFF SAW Initial START-UP/OPERATIONFuel Check StartingSHS62A CUT-OFF SAW Initial START-UP/OPERATION Shut-downBelt Changing Procedure KnobCover Guard Until the V-belt is completely slackedSHS62A CUT-OFF SAW Maintenance Re-install the guardV-belt should remain in tension Tensioning positionReversing the Cutting Arm Procedure Cam .The V-belt should remain in tension Re-attach the cover guardSHS62A CUT-OFF SAW Maintenance AIR/FUEL Filter Air/Fuel Filter Maintenance ProceduresSHS62A CUT-OFF SAW Troubleshooting Blade SHS62A CUT-OFF SAW Troubleshooting Engine Troubleshooting EngineTroubleshooting Engine Spark plug heat value improper?SHS62A CUT-OFF SAW Filter Kits Includes 1 eaSHS62A CUT-OFF SAW Explanation of Parts Section Remarks NO. ColumnPart NO. Column QTY. ColumnSHS62A CUT-OFF SAW Suggested Spare Parts To 3 UnitsSHS62A CUT-OFF SAW Muffler Assy Part Name SHS62A CUT-OFF SAW Recoil Start Assy HANDLE, Starter Rope SHS62A CUT-OFF SAW Crankcase Assy Plate SHS62A CUT-OFF SAW V-BELT Cover Clutch Side Assy SHS62A CUT-OFF SAW V-BELT Cover Clutch Side Assy SHS62A CUT-OFF SAW V-BELT Cover Pulley /BLADE Guard Part Name QTY SHS62A CUT-OFF SAW Fuel Tank Assy Part Name QTY Remarks SHS62A CUT-OFF SAW Lifting Handle and Roller Assy SHS62A CUT-OFF SAW Lifting Handle and Roller Assy SHS62A CUT-OFF SAW -THROTTLE Linkage Assy Spring SHS62A CUT-OFF SAW Flywheel Cover Assy WASHER, Flat SHS62A CUT-OFF SAW Flywheel Assy Pawl SET SHS62A CUT-OFF SAW Ignition Coil Assy Spring Spark Plug SHS62A CUT-OFF SAW AIR Filter Assy FLANGE, PRE- FILTER, CAP SHS62A CUT-OFF SAW Carburetor Mounting Assy Carburetor Mounting Assy SHS62A CUT-OFF SAW Carburetor Assy Throttle Shaft SHS62A CUT-OFF SAW Crankshaft / Piston Assy SHS62A CUT-OFF SAW Crankshaft and Piston Assy SHS62A CUT-OFF SAW Water KIT Assy VALVE, SHUT-OFF SHS62A CUT-OFF SAW Tools HS4191240 00325Recommended Diamond Blades For Your Side Winder Saw SHS62A CUT-OFF SAW Recommended Diamond BladesTerms and Conditions of Sale Terms and Conditions of Sale PartsHeres HOW to GET Help