Stow SHS62A manual Reversing the Cutting Arm Procedure

Page 23

SHS62A CUT-OFF SAW — MAINTENANCE

Reversing the Cutting Arm Procedure

NOTE

This assembly procedure permits the operator to reorient the cutting blade closer to a wall, column

 

and/or object.

 

 

 

The Stow Side Winder Cut-Off Saw comes with a Tool Kit

 

 

 

(Figure 16) that assist you with day to day operations.You will

 

 

 

need these tools for the maintenance of your saw.

 

 

 

Item Gis a versatile screwdriver/wrench that accommodates

 

 

 

common bolt/screw and nut head sizes of your saw.

 

 

 

Item His the wrench necessary to accommodate various allen

 

 

 

 

 

 

screws.

 

Figure 20. Tool Kit

 

 

 

This position displays the cutting blade on the inside (center)

 

 

 

cutting position.To reverse the blade position continue with the

 

 

 

following steps:

 

 

 

Remove the following items from the Cutting Arm Assembly

 

 

 

to expose the V-belt:

 

 

 

Guard Adjustment Knob

Two Cap Screws

Cover Guard

Figure 21. Inside Center Cutting Position

Loosen the belt tensioning cam

and remove the three

nuts

.This will take tension off the V-belt, and permit you to

reverse the cutting arm.

 

Figure 22. Belt Tensioning Cam

SHS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (06/02/06) — PAGE 23

Image 23
Contents SideWinder Page Page SHS62A CUT-OFF SAW Table of Contents SHS62A CUT-OFF SAW Parts Ordering Procedures SHS62A CUT-OFF SAW Safety Message Alert Symbols Rotating blade can cut and crush. Keep hands and feet clear SHS62A CUT-OFF SAW Safety Message Alert SymbolsAlways wear approved eye and hearing protection SHS62A CUT-OFF SAW Rules for Safe Operation SHS62A CUT-OFF SAW Rules for Safe Operation General SafetyNever use carbide-tipped or toothed type blades of any kind Diamond Blade SafetySaw Transportation Safety Always know the location of the nearest first aid kit SHS62A CUT-OFF SAW Rules for Safe OperationEngine Speed 10,000 DisplacementDimensions LxWxH Engine TypeMachine Operation And Safety Decals SHS62A CUT-OFF SAW Decal Placement10 9 8 7 6 SHS62A CUT-OFF SAW Controls & Components Blade shaft SHS62A CUT-OFF SAW Blade Installation InstructionsFasten the clamp to the Roller Bar Support Arm SHS62A CUT-OFF SAW Water KIT Installation InstructionsDiamond Blade SHS62A CUT-OFF SAW BladesStarting Place the engine ON/OFF switch in the on positionSHS62A CUT-OFF SAW Initial START-UP/OPERATION Fuel CheckShut-down SHS62A CUT-OFF SAW Initial START-UP/OPERATIONUntil the V-belt is completely slacked Belt Changing ProcedureKnob Cover GuardTensioning position SHS62A CUT-OFF SAW MaintenanceRe-install the guard V-belt should remain in tensionReversing the Cutting Arm Procedure Re-attach the cover guard Cam .The V-belt should remain in tensionAir/Fuel Filter Maintenance Procedures SHS62A CUT-OFF SAW Maintenance AIR/FUEL FilterSHS62A CUT-OFF SAW Troubleshooting Blade Troubleshooting Engine SHS62A CUT-OFF SAW Troubleshooting EngineSpark plug heat value improper? Troubleshooting EngineIncludes 1 ea SHS62A CUT-OFF SAW Filter KitsQTY. Column SHS62A CUT-OFF SAW Explanation of Parts Section RemarksNO. Column Part NO. ColumnTo 3 Units SHS62A CUT-OFF SAW Suggested Spare PartsSHS62A CUT-OFF SAW Muffler Assy Part Name SHS62A CUT-OFF SAW Recoil Start Assy HANDLE, Starter Rope SHS62A CUT-OFF SAW Crankcase Assy Plate SHS62A CUT-OFF SAW V-BELT Cover Clutch Side Assy SHS62A CUT-OFF SAW V-BELT Cover Clutch Side Assy SHS62A CUT-OFF SAW V-BELT Cover Pulley /BLADE Guard Part Name QTY SHS62A CUT-OFF SAW Fuel Tank Assy Part Name QTY Remarks SHS62A CUT-OFF SAW Lifting Handle and Roller Assy SHS62A CUT-OFF SAW Lifting Handle and Roller Assy SHS62A CUT-OFF SAW -THROTTLE Linkage Assy Spring SHS62A CUT-OFF SAW Flywheel Cover Assy WASHER, Flat SHS62A CUT-OFF SAW Flywheel Assy Pawl SET SHS62A CUT-OFF SAW Ignition Coil Assy Spring Spark Plug SHS62A CUT-OFF SAW AIR Filter Assy FLANGE, PRE- FILTER, CAP SHS62A CUT-OFF SAW Carburetor Mounting Assy Carburetor Mounting Assy SHS62A CUT-OFF SAW Carburetor Assy Throttle Shaft SHS62A CUT-OFF SAW Crankshaft / Piston Assy SHS62A CUT-OFF SAW Crankshaft and Piston Assy SHS62A CUT-OFF SAW Water KIT Assy VALVE, SHUT-OFF SHS62A CUT-OFF SAW Tools 00325 HS4191240SHS62A CUT-OFF SAW Recommended Diamond Blades Recommended Diamond Blades For Your Side Winder SawTerms and Conditions of Sale Parts Terms and Conditions of SaleHeres HOW to GET Help