Stow manual SHS62A CUT-OFF SAW Troubleshooting Blade

Page 26

SHS62A CUT-OFF SAW — TROUBLESHOOTING (BLADE)

TABLE 3. BLADE TROUBLESHOOTING

SYMPTOM

POSSIBLE PROBLEM

SOLUTION

 

 

 

 

Blade too hard for the material being

Consult Dealer or Multiquip for correct blade. Try cutting

 

very soft material (sandstone, silica brick, cinder block) to

 

cut?

 

"Redress" the blade.

 

 

 

 

 

 

Engine torque diminished because of

Tighten and/or replace V-Belts.

 

loose V-belt?

 

 

Blade slows or stops cutting.

 

 

Insufficient engine power?

Check throttle setting.

 

 

 

 

 

Improper direction of rotation?

Check that the blade is properly oriented and rotational

 

arrow points in a "Down-Cutting" direction.

 

 

 

 

 

 

Blade is slipping on the blade shaft?

Check that the blade & flange pin are properly installed on

 

the blade shaft.

 

 

 

 

 

 

Blade being used on misaligned saw?

Check blade shaft bearings and alignment integrity.

 

 

 

 

Blade is excessively hard for the

Check specification of the blade with the material being

 

material being cut?

cut. Consult Dealer or Multiquip for information.

 

 

 

Blade does not cut straight

Blade being used at improper RPM?

Ensure blade surface feet per minute speed (SFPM) is

approximately 6,000.

and/or true.

 

 

 

 

Blade improperly mounted on arbor

Ensure blade is properly affixed on the blade shaft.

 

shoulders and flanges?

 

 

 

 

 

 

Excessive force applied to blade while

DO NOT force the blade in the cut. Apply a slow and

 

cutting?

steady pace when sawing.

 

 

 

 

Blades too hard for the material being

Consult Dealer or Multiquip for correct blade. Try cutting

 

very soft material (sandstone, silica brick, cinder block) to

 

cut?

 

"Redress" the blade.

 

 

 

 

 

 

Blade improperly mounted on arbor

Ensure blade is properly affixed on the blade shaft.

 

shoulders and flanges?

 

 

 

 

 

 

Blade not receiving enough cooling

Ensure proper flow & volume of water is provided for wet

 

cutting blades. Ensure sufficient cooling air is circulated

Blade discoloring, crackling

water or air?

about a dry cutting blade.

and/or wearing excessively.

 

 

 

 

Arbor hole out of round?

Ensure blade is properly affixed on the blade shaft.

 

 

 

 

Incorrect blade chosen for material

Check specification of the blade with the material being

 

being cut?

cut. Consult Dealer or Multiquip for information.

 

 

 

 

Excessive force applied to blade while

DO NOT force the blade in the cut. Apply a slow and

 

cutting?

steady pace when sawing.

 

 

 

PAGE 26 — SHS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (06/02/06)

Image 26
Contents SideWinder Page Page SHS62A CUT-OFF SAW Table of Contents SHS62A CUT-OFF SAW Parts Ordering Procedures SHS62A CUT-OFF SAW Safety Message Alert Symbols Rotating blade can cut and crush. Keep hands and feet clear SHS62A CUT-OFF SAW Safety Message Alert SymbolsAlways wear approved eye and hearing protection SHS62A CUT-OFF SAW Rules for Safe Operation General Safety SHS62A CUT-OFF SAW Rules for Safe OperationNever use carbide-tipped or toothed type blades of any kind Diamond Blade SafetySaw Transportation Safety SHS62A CUT-OFF SAW Rules for Safe Operation Always know the location of the nearest first aid kitEngine Type DisplacementDimensions LxWxH Engine Speed 10,000SHS62A CUT-OFF SAW Decal Placement Machine Operation And Safety Decals10 9 8 7 6 SHS62A CUT-OFF SAW Controls & Components SHS62A CUT-OFF SAW Blade Installation Instructions Blade shaftSHS62A CUT-OFF SAW Water KIT Installation Instructions Fasten the clamp to the Roller Bar Support ArmSHS62A CUT-OFF SAW Blades Diamond BladeFuel Check Place the engine ON/OFF switch in the on positionSHS62A CUT-OFF SAW Initial START-UP/OPERATION StartingSHS62A CUT-OFF SAW Initial START-UP/OPERATION Shut-downCover Guard Belt Changing ProcedureKnob Until the V-belt is completely slackedV-belt should remain in tension SHS62A CUT-OFF SAW MaintenanceRe-install the guard Tensioning positionReversing the Cutting Arm Procedure Cam .The V-belt should remain in tension Re-attach the cover guardSHS62A CUT-OFF SAW Maintenance AIR/FUEL Filter Air/Fuel Filter Maintenance ProceduresSHS62A CUT-OFF SAW Troubleshooting Blade SHS62A CUT-OFF SAW Troubleshooting Engine Troubleshooting EngineTroubleshooting Engine Spark plug heat value improper?SHS62A CUT-OFF SAW Filter Kits Includes 1 eaPart NO. Column SHS62A CUT-OFF SAW Explanation of Parts Section RemarksNO. Column QTY. ColumnSHS62A CUT-OFF SAW Suggested Spare Parts To 3 UnitsSHS62A CUT-OFF SAW Muffler Assy Part Name SHS62A CUT-OFF SAW Recoil Start Assy HANDLE, Starter Rope SHS62A CUT-OFF SAW Crankcase Assy Plate SHS62A CUT-OFF SAW V-BELT Cover Clutch Side Assy SHS62A CUT-OFF SAW V-BELT Cover Clutch Side Assy SHS62A CUT-OFF SAW V-BELT Cover Pulley /BLADE Guard Part Name QTY SHS62A CUT-OFF SAW Fuel Tank Assy Part Name QTY Remarks SHS62A CUT-OFF SAW Lifting Handle and Roller Assy SHS62A CUT-OFF SAW Lifting Handle and Roller Assy SHS62A CUT-OFF SAW -THROTTLE Linkage Assy Spring SHS62A CUT-OFF SAW Flywheel Cover Assy WASHER, Flat SHS62A CUT-OFF SAW Flywheel Assy Pawl SET SHS62A CUT-OFF SAW Ignition Coil Assy Spring Spark Plug SHS62A CUT-OFF SAW AIR Filter Assy FLANGE, PRE- FILTER, CAP SHS62A CUT-OFF SAW Carburetor Mounting Assy Carburetor Mounting Assy SHS62A CUT-OFF SAW Carburetor Assy Throttle Shaft SHS62A CUT-OFF SAW Crankshaft / Piston Assy SHS62A CUT-OFF SAW Crankshaft and Piston Assy SHS62A CUT-OFF SAW Water KIT Assy VALVE, SHUT-OFF SHS62A CUT-OFF SAW Tools HS4191240 00325Recommended Diamond Blades For Your Side Winder Saw SHS62A CUT-OFF SAW Recommended Diamond BladesTerms and Conditions of Sale Terms and Conditions of Sale PartsHeres HOW to GET Help