Graco XP70 important safety instructions Shutdown, Park

Page 28

Shutdown

6.Run the pumps until the A and B hoppers (J) are empty. Salvage the material in separate, clean con- tainers.

7.Close the main air shutoff valve (CA).

CA

r_571100_3A0420A_11a-1

8.Wipe the hoppers (J) clean, then add solvent to each. Move the circulation lines (U) to waste con- tainers and push out the dirty fluids.

9.Move the recirculation lines (U) back to the hoppers. Continue recirculating until the system is thoroughly flushed.

U

J

10.Close the circulation handle (AC) and open the dual shutoff handle (AE).

11.Dispense fresh solvent through the mix manifold valves and out the gun. Turn off the air motors and relieve all pressures.

AC

AE

AD

12.Close the dual shutoff handle (AE).

13.Remove pump fluid filters, if installed, and soak in solvent. Clean and replace the filter cap. Always replace the filter o-rings.

NOTE:

Fill the A and B pump packing nuts with TSL. Also, always leave some type of fluid, such as solvent or oil, in the system to prevent scale build up. This build up can flake off later. Do not use water.

If machine is set up with a remote mix manifold, the A and B hose can be disconnected from the mix manifold, and secured in back of each hop- per for circulation of flush solvent.

Change the flush solvent at least once until it circulates clean.

Always keep the A side and B side flush solvent separate.

Shutdown

1.Follow Pressure Relief Procedure, page 20.

2.Flush mix manifold, hoses, and gun. See Flush Mix Manifold, Hose, and Spray Gun, page 26.

3.Close the main air shutoff valve (CA).

Park

1.Open the circulation handle (AC) and adjust the air regulator (CB) so that the pump runs slowly.

2.Close the circulation handle (AC) when the pump is at the bottom of the stroke.

3.Close the air regulator (CB) and open the circulation handle (AC).

28

3A0420H

Image 28
Contents XP70 Plural-Component Sprayer Contents Related Manuals Manual DescriptionFire and Explosion Hazard Skin Injection Hazard Toxic Fluid or Fumes Hazard Important Two-Component Material Information B Component Designations Changing MaterialsMachine Left Machine Right Market Equipment Designations Usage OverviewOver Pressure Protection Initial System Setup Cart-Mounted XP70 Sprayers ModelsBare Proportioning Pump Packages Component Identification Mounting Components forFluid Control Assembly Main Air ControlsSolvent Flush Pump Kit 262393 optional Included with optional solvent flush pump kit KeyFluid Line Accessories Flush Before Using EquipmentOptional Accessories Air LineLocation SetupGrounding Wire Sprayers with Explosion-Proof Heaters Hazardous location sprayers onlyAir Motor Position Position Air MotorConnect Fluid Hose Bundles Remote Only Connect Air SupplyConnect Static Mixers, Gun, and Hoses Pressure Relief Procedure Relieve a and B Fluid PressurePrime Empty Sprayer Prime a and B FluidsPrime Solvent Flush Pump Recirculate or Re-Prime After a Pump Runs Dry Without HeatWith Heat Heat FluidSpray Side Mix Manifold Restriction Follow Pressure Relief Procedure, Flush Mixed MaterialFlush Mix Manifold, Hose, and Spray Gun Use Optional Solvent PumpProcedure GuidelinesShutdown ParkSystem Verification Maintenance Troubleshooting Problem Cause SolutionPump Troubleshooting Pump Assembly Remove Pump AssemblyRemove Displacement Pump RepairReplace Air Control Assembly Air ControlsRemove Air Motor Replace Air Filter ElementAir Control Assembly Air FlowFluid Circulation Manifold Mix Manifold AssemblyReplace Drain Valve Cartridges Repair Hoppers Solvent PumpOptional Fluid Heaters Service and RepairReplace Parts Cart-Mounted XP70 Sprayer49 a 49 B 27, 28 32 27 Common Parts Part Description QtyParts Varying by Model with Hoppers Parts Varying by Model with No HoppersBare Proportioning Pump Package 122 106 105 135 117 108 101 138 139 140Ratio Description Varying Parts571100 571150 571200 571250 571300 571400 Qty 202 211 205 209 210 Ref. No. Part No. Description QtyFluid Manifold Part No. Description QtyPump Repair Kits Recommended Spare PartsPump Filter O-rings packs Pump Performance Charts Calculate Fluid Outlet PressureCalculate Pump Air Flow/Consumption 11 or 21 Mix RatioMix Ratio Pump Performance Charts31 Mix Ratio Bar MPaPsig PressureAcceptable For Use in Explosive Atmospheres Accessories and KitsNot Approved For Explosive Atmospheres Technical Data Psi MPa, bar Psi MPa, psi Gpm ltr/minDimensions Floor Mounting Dimensions Top VIewTop VIew Side VIewBare Proportioner Mounting Hole Dimensions Graco Standard Warranty Graco Information