Graco XP70 important safety instructions Skin Injection Hazard

Page 5

Warnings

WARNING

SKIN INJECTION HAZARD

High-pressure fluid from gun, hose leaks, or ruptured components will pierce skin. This may look like just a cut, but it is a serious injury that can result in amputation. Get immediate surgical treatment.

•Do not spray without tip guard and trigger guard installed.

•Engage trigger lock when not spraying.

•Do not point gun at anyone or at any part of the body.

•Do not put your hand over the spray tip.

•Do not stop or deflect leaks with your hand, body, glove, or rag.

•Follow the Pressure Relief Procedure when you stop spraying and before cleaning, checking, or ser- vicing equipment.

•Tighten all fluid connections before operating the equipment.

•Check hoses and couplings daily. Replace worn or damaged parts immediately.

EQUIPMENT MISUSE HAZARD

Misuse can cause death or serious injury.

•Do not operate the unit when fatigued or under the influence of drugs or alcohol.

•Do not exceed the maximum working pressure or temperature rating of the lowest rated system com- ponent. See Technical Data in all equipment manuals.

•Use fluids and solvents that are compatible with equipment wetted parts. See Technical Data in all equipment manuals. Read fluid and solvent manufacturer’s warnings. For complete information about your material, request MSDS from distributor or retailer.

•Do not leave the work area while equipment is energized or under pressure. Turn off all equipment and follow the Pressure Relief Procedure when equipment is not in use.

•Check equipment daily. Repair or replace worn or damaged parts immediately with genuine manufac- turer’s replacement parts only.

•Do not alter or modify equipment.

•Use equipment only for its intended purpose. Call your distributor for information.

•Route hoses and cables away from traffic areas, sharp edges, moving parts, and hot surfaces.

•Do not kink or over bend hoses or use hoses to pull equipment.

•Keep children and animals away from work area.

•Comply with all applicable safety regulations.

MOVING PARTS HAZARD

Moving parts can pinch, cut or amputate fingers and other body parts.

•Keep clear of moving parts.

•Do not operate equipment with protective guards or covers removed.

•Pressurized equipment can start without warning. Before checking, moving, or servicing equipment, follow the Pressure Relief Procedure and disconnect all power sources.

3A0420H

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents XP70 Plural-Component Sprayer Contents Manual Description Related ManualsFire and Explosion Hazard Skin Injection Hazard Toxic Fluid or Fumes Hazard Important Two-Component Material Information Machine Left Machine Right Market Equipment Designations Changing MaterialsB Component Designations Over Pressure Protection OverviewUsage Initial System Setup Bare Proportioning Pump Packages ModelsCart-Mounted XP70 Sprayers Mounting Components for Component IdentificationMain Air Controls Fluid Control AssemblyIncluded with optional solvent flush pump kit Key Solvent Flush Pump Kit 262393 optionalFlush Before Using Equipment Fluid Line AccessoriesOptional Accessories Air LineGrounding SetupLocation Hazardous location sprayers only Wire Sprayers with Explosion-Proof HeatersPosition Air Motor Air Motor PositionConnect Static Mixers, Gun, and Hoses Connect Air SupplyConnect Fluid Hose Bundles Remote Only Relieve a and B Fluid Pressure Pressure Relief ProcedurePrime a and B Fluids Prime Empty SprayerPrime Solvent Flush Pump Without Heat Recirculate or Re-Prime After a Pump Runs DryWith Heat Heat FluidSpray Side Mix Manifold Restriction Flush Mixed Material Follow Pressure Relief Procedure,Flush Mix Manifold, Hose, and Spray Gun Use Optional Solvent PumpGuidelines ProcedurePark ShutdownSystem Verification Maintenance Problem Cause Solution TroubleshootingPump Troubleshooting Remove Pump Assembly Pump AssemblyRemove Displacement Pump RepairAir Controls Replace Air Control AssemblyRemove Air Motor Replace Air Filter ElementAir Flow Air Control AssemblyReplace Drain Valve Cartridges Mix Manifold AssemblyFluid Circulation Manifold Repair Solvent Pump HoppersReplace Service and RepairOptional Fluid Heaters Cart-Mounted XP70 Sprayer Parts49 a 49 B 27, 28 32 27 Part Description Qty Common PartsParts Varying by Model with No Hoppers Parts Varying by Model with Hoppers122 106 105 135 117 108 101 138 139 140 Bare Proportioning Pump Package571100 571150 571200 571250 571300 571400 Qty Varying PartsRatio Description Ref. No. Part No. Description Qty 202 211 205 209 210Part No. Description Qty Fluid ManifoldPump Filter O-rings packs Recommended Spare PartsPump Repair Kits Calculate Fluid Outlet Pressure Pump Performance ChartsCalculate Pump Air Flow/Consumption 11 or 21 Mix Ratio31 Mix Ratio Pump Performance ChartsMix Ratio MPa BarPsig PressureNot Approved For Explosive Atmospheres Accessories and KitsAcceptable For Use in Explosive Atmospheres Psi MPa, bar Psi MPa, psi Gpm ltr/min Technical DataFloor Mounting Dimensions Top VIew DimensionsTop VIew Side VIewBare Proportioner Mounting Hole Dimensions Graco Information Graco Standard Warranty
Top Page Image Contents