Graco 3A0420T important safety instructions Skin Injection Hazard

Page 5

Warnings

WARNING

SKIN INJECTION HAZARD

High-pressure fluid from gun, hose leaks, or ruptured components will pierce skin. This may look like just a cut, but it is a serious injury that can result in amputation. Get immediate surgical treatment.

•Do not spray without tip guard and trigger guard installed.

•Engage trigger lock when not spraying.

•Do not point gun at anyone or at any part of the body.

•Do not put your hand over the spray tip.

•Do not stop or deflect leaks with your hand, body, glove, or rag.

•Follow the Pressure Relief Procedure when you stop spraying and before cleaning, checking, or servicing equipment.

•Tighten all fluid connections before operating the equipment.

•Check hoses and couplings daily. Replace worn or damaged parts immediately.

EQUIPMENT MISUSE HAZARD

Misuse can cause death or serious injury.

•Do not operate the unit when fatigued or under the influence of drugs or alcohol.

•Do not exceed the maximum working pressure or temperature rating of the lowest rated system com- ponent. See Technical Data in all equipment manuals.

•Use fluids and solvents that are compatible with equipment wetted parts. See Technical Data in all equipment manuals. Read fluid and solvent manufacturer’s warnings. For complete information about your material, request MSDS from distributor or retailer.

•Do not leave the work area while equipment is energized or under pressure. Turn off all equipment and follow the Pressure Relief Procedure when equipment is not in use.

•Check equipment daily. Repair or replace worn or damaged parts immediately with genuine manufac- turer’s replacement parts only.

•Do not alter or modify equipment.

•Use equipment only for its intended purpose. Call your distributor for information.

•Route hoses and cables away from traffic areas, sharp edges, moving parts, and hot surfaces.

•Do not kink or over bend hoses or use hoses to pull equipment.

•Keep children and animals away from work area.

•Comply with all applicable safety regulations.

MOVING PARTS HAZARD

Moving parts can pinch, cut or amputate fingers and other body parts.

•Keep clear of moving parts.

•Do not operate equipment with protective guards or covers removed.

•Pressurized equipment can start without warning. Before checking, moving, or servicing equipment, follow the Pressure Relief Procedure and disconnect all power sources.

3A0420T

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents XP Proportioners Contents Related Manuals Fire and Explosion Hazard Skin Injection Hazard Toxic Fluid or Fumes Hazard Important Two-Component Material Information Equipment Designations Changing MaterialsB Component Designations Over Pressure Protection OverviewUsage Initial System Setup Cart-Mounted Systems ModelsPump Volume Max Fluid Max Air Mix Gallon Building systems with bare proportioning pump Bare Proportioning Pump PackagesPackages Over Pressure Protection must be used, seeMounting Components for Component IdentificationMain Air Controls Fluid Control AssemblyAir Controls Solvent Flush Pump Kit 262393 optionalPump Key Flush Before Using Equipment Fluid Line AccessoriesOptional Accessories Air LineGrounding SetupLocation Hazardous location systems only Wire Systems with Explosion-Proof HeatersChange Motor Position Motor PositionCheck Motor Position Connect Static Mixers, Gun, and Hoses Connect Air SupplyConnect Fluid Hose Bundles Remote Mix Manifold Only Relieve a and B Fluid Pressure Pressure Relief ProcedurePrime a and B Fluids Prime Empty SystemPrime Solvent Flush Pump Follow Prime Empty System, Heat FluidSpray Side Mix Manifold Restriction To Adjust the RestrictorFlush Mixed Material Follow Pressure Relief Procedure,Flush Mix Manifold, Hose, and Spray Gun Use Optional Solvent PumpGuidelines ProcedurePark ShutdownSystem Verification Maintenance Problem Cause Solution TroubleshootingHardener Pump Falling Pump TroubleshootingTrouble Area Resin Pump Leakage Resin PumpRemove Pump Assembly Pump AssemblyRemove Displacement Pump RepairRemove Motor Replace Air Control AssemblyReplace Air Filter Element Replace System Air RegulatorAir Flow Air Control AssemblyReplace Over Pressure Relief Valves Mix Manifold AssemblyFluid Circulation Manifold with Over Pressure Relief Valves Circulation Fluid Circulation Manifold Replacement GuideTarget Opening Manifold Valve Pressure Color Psi MPa, bar Use withOptional Solvent Pump HoppersReplace Service and RepairOptional Fluid Heaters Cart-Mounted System PartsStandard Mix Manifold Models Quickset Mix Manifold Models Washer Parts Common to All Systems Description QtyParts Varying By Model XP35 Systems Ref Part Description Coupling 283101 283102 283201 283202 283301 283302 283401 283402 Parts Varying By Model XP70 Systems Part Description Model 571100 shown Bare Proportioning Pump PackageParts Varying by Pump Package Parts Common to All Pump PackagesQty Ref. No. Part No. Description Air ControlsFluid Circulation Manifold with Over Pressure Relief Valve Assembly 262784 XP35 262783 XP50 262806 XP70Part Description Qty Ref Manifold to also fit Series a XP Proportioners withPump Repair Kits Recommended Spare PartsPump Filter O-rings packs Recirculation/Overpressure valve seeAcceptable For Use in Explosive Atmospheres Accessories and KitsNot Approved For Explosive Atmospheres Technical Data Side View DimensionsTop View Floor Mounting Dimensions, Top View Bare Proportioner Mounting Hole Dimensions Wall Mount Bracket 262812 Dimensions Hydraulic Unit Dimensions Floor Stand 24M281 DimensionsDimensions 3A0420T Graco Information Graco Standard Warranty
Top Page Image Contents