Graco 310692C manual Technical Data, Category

Page 33

Technical Data

Technical Data

Category

Maximum Working Fluid Pressure

Maximum Working Air Pressure

Maximum Compliant Inbound Air Pressure

HVLP Gravity/Siphon Feeds

HVLP Pressure Feed

Fluid and Air Operating Temperature Range

Weight

Air Inlet

Fluid Inlet

Wetted Parts

Noise Data*

Sound Pressure

Sound Power

Air Consumption Gravity/Siphon Feed:

Airspray at 50 psi inlet

HVLP at 29 psi inlet

Compliant at 29 psi inlet

Air Consumption Pressure Feed:

Airspray at 40 psi inlet

HVLP at 40 psi inlet

Compliant at 29 psi inlet

*All readings were taken with the gun controls fully open and with 40 psi (280 kPa, 2.8 bar). Sound pressure was tested to CAGI-PNUEROP-1969. Sound power was tested to ISO 3744-1981.

Data

300 psi (2.1 MPa, 21 bar)

100 psi (0.7 MPa, 7 bar)

29 psi (200 kPa, 2.0 bar)

29 psi (200 kPa, 2.0 bar)

40 psi (280 kPa, 2.8 bar) 32°F to 109°F (0°C to 43°C)

22.3oz. (632 g)

1/4-18 npsm 3/8 npsm

304, 303,17-4 PH Stainless Steel, PEEK, Acetal, Ultra High Molecular Weight Polyethylene

84.4Db(A)

94.0Db(A)

14.1scfm

15.5scfm

11.2scfm

12.5scfm

21.0scfm

11.2scfm

310692C

33

Image 33
Contents Delta Spray XT Gun Contents Manual ConventionsRelated Manuals Pressurized Equipment Hazard Fire and Explosion Hazard FE CED/IND GeneralPressure feed spray guns Selection ChartsPressure feed spray guns with 1 quart pressure feed cup Siphon feed spray gunsGravity feed spray guns with 16 oz. gravity cup Gravity feed spray guns without gravity cupGravity feed spray guns with 3M PPS gravity cup Orifice sizeAir Caps Gun SelectionHvlp Guns Compliant GunsNozzle, Needle, and Tip Selection Nozzle Orifice FluidNozzle Assy Tip Kit Uses Installation Top and bottom feed gunsKey Setup Connecting the air lineFlushing the gun Connecting the fluid supply Connecting the fluid hosePositioning the Air Cap Pressure feed guns onlyWarining Adjusting the Spray PatternSetup Operation Pressure Relief ProcedureApplying the Fluid IncorrectGeneral maintenance Daily Gun MaintenanceFlushing and cleaning Gravity and Siphon Feed GunsPressure Feed Guns Install the air cap retaining ring assembly 15 and air cap Ti4848a Troubleshooting Service Replacing the air and fluid packingsDisassembling the gun Replacing the spray housing o-rings and packings Replacing the pattern adjustment valve packings Replacing the fluid valve packings Reassembling the gun Ti4849i Service 310692C Airspray, HVLP, and Compliant Guns PartsSpray Housing Gun AssemblyPart No. Description Qty Spatter or Specking Airspray Gun Spatter or Specking Airspray Gun Accessories Gravity Cup Gun Air Regulator AssyGravity Cup Holder Bracket SST Pressure Cup Kit 239802 with single air regulator3M PPS Paint Preparation System SST Pressure Cup Kit 239803 with double air regulatorDisposable Polythylene Cup Liners Fluid Shut Off SpringTechnical Data CategoryData Graco Information Graco Standard Warranty