Spray Tip Selection Chart
Spray Tip Selection Chart
Spray Tips, for use with G15/G40 Air Cap
AAM Fine Finish Spray Tips
Recommended for high finish quality applications at low and medium pressures. Order desired tip, Part No. AAMxxx, where xxx =
GG4 Industrial Spray Tips
Recommended for high wear applications at high pressures.
Order desired tip, Part No. GG4xxx, where xxx =
NOTE:
•All tips in the Spray Tip Selection Chart below can be used with Model G40 guns. Use tips in the gray shaded area of the chart with Model G40 guns only.
•Do not use tips in the gray shaded area of the chart with Model G15 guns.
Do not use tips in the gray shaded area of the Spray Tip Selection Chart with Model G15 guns. G15 guns are not designed for use at high pressures. Failure to follow this warning can result in serious injury, includ- ing fluid injection and splashing in the eyes or on the skin.
|
| * Fluid Output |
|
| Maximum Pattern Width at 12 in. (305 mm) |
| |||||||
|
| fl oz/min (lpm) |
|
|
|
| in. (mm) |
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
| |
| at 600 psi | at 1000 psi | 2 to 4 | 4 to 6 | 6 to 8 | 8 to 10 | 10 to 12 | 12 to 14 | 14 to 16 | 16 to 18 | 18 to 20 | ||
| (100) | (150) | (200) | (250) | (300) | (350) | (400) | (450) | (500) | ||||
Orifice Size | (4.1 MPa, | (7.0 MPa, | |||||||||||
|
|
|
|
|
|
|
|
| |||||
in. (mm) | 41 bar) | 70 bar) |
|
|
|
| Spray Tip |
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
| ||
† 0.007 (0.178) | 4.0 (0.1) | 5.2 (0.15) | ★107 | 207 | 307 |
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
| ||
† 0.009 (0.229) | 7.0 (0.2) | 9.1 (0.27) | 109 | 209 | 309 | 409 | 509 |
|
|
|
| ||
† 0.011 (0.279) | 9.5 (0.28) | 12.5 (0.37) | 111 | 211 | 311 | 411 | 511 | 611 | ❄711 |
|
| ||
0.013 (0.330) | 12.0 | (0.35) | 16.0 (0.47) |
| 213 | 313 | 413 | 513 | 613 | 713 |
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
0.015 (0.381) | 16.0 | (0.47) | 21.0 (0.62) |
| 215 | 315 | 415 | 515 | 615 | 715 | 815 |
| |
0.017 (0.432) | 20.0 | (0.59) | 26.5 (0.78) |
| 217 | 317 | 417 | 517 | 617 | 717 | 817 | 917 | |
0.019 (0.483) | 28.0 | (0.8) | 36.3 (1.09) |
| 219 | 319 | 419 | 519 | 619 | 719 | 819 | 919 | |
|
|
|
|
|
|
|
|
|
|
|
|
| |
0.021 (0.533) | 35.0 | (1.0) | 45.4 (1.36) |
|
| 321 | 421 | 521 | 621 | 721 | 821 | 921 | |
‡ 0.023 (0.584) | 40.0 | (1.2) | 51.9 (1.56) |
|
|
| 423 | 523 | 623 | 723 |
| 923 | |
‡ 0.025 (0.635) | 50.0 | (1.5) | 64.8 (1.94) |
|
|
| 425 |
| 625 | 725 | 825 | ★925 | |
‡ 0.027 (0.686) | 58.5 | (1.7) | 75.8 (2.27) |
|
|
|
| 527 | 627 |
| 827 |
| |
‡ 0.029 (0.737) | 68.0 | (1.9) | 88.2 (2.65) |
|
|
|
|
| 629 |
|
|
| |
‡ 0.031 (0.787) | 78.0 | (2.2) | 101.1 (3.03) |
|
|
| 431 |
| 631 |
|
|
| |
‡ 0.033 (0.838) | 88.0 | (2.5) | 114.1 (3.42) |
|
|
|
|
| 633 |
| ★833 |
| |
‡ 0.035 (0.889) | 98.0 | (2.8) | 127.1 (3.81) |
|
|
| 435 |
|
|
|
|
| |
‡ 0.037 (0.940) | 108.0 (3.1) | 140.0 (4.20) |
|
|
|
|
|
| 737 |
|
| ||
‡ 0.039 (0.991) | 118.0 (3.4) | 153.0 (4.59) |
|
|
|
| 539 | 639 |
| 839 |
| ||
*Tips are tested in water.
Fluid output (Q) at other pressures (P) can be calculated by this formula: Q = (0.041) (QT) 
P where QT = fluid output (fl oz/min) at 600 psi from the above table for the selected orifice size.
† | These tip sizes include a 150 mesh tip filter. | ★ GG4 tips only. |
‡ | Do not use these tips with Model G15 guns. | ❄ AAM tips only. |
32 | 3A0149C |